أداة 121 / 136

Blister Material Requirement Calculator — US Units

Blister Material Requirement connects the figures on a US supplier quote with the quantity used by your packaging operation. Have target good packs (units), common web width (inch), machine pitch (inch) ready before you start.

مواصفاتك

وحدة
وحدة
g/m²
g/m²
%
تتحدّث النتائج أثناء التعديل. لا يُحفظ شيء حتى تختار الحفظ.
حساب فوري

إجمالي مادتي التشكيل والغطاء

95.15 lb
إجمالي الطول الطولي لكل شريط1,151.17 ft
إجمالي مادة التشكيل81.22 lb
إجمالي مادة الغطاء13.92 lb
المساحة الإجمالية لكل شريط1,133.04 ft²

الفاقد نسبة مفقودة من إجمالي المدخلات. الاحتياج الإجمالي = المخرجات المطابقة ÷ (1 − الفاقد/100).

يفترض النموذج تساوي عرض وخطوة شريطي التشكيل والغطاء. أضف فاقد بدء التشغيل الثابت منفصلًا؛ الاحتياج مادة إجمالية مستمرة دون تقريب لدورات ماكينة كاملة.

Gross packs = Good target ÷ (1 − Waste fraction); Web length(ft) = Gross packs × Pitch(in) ÷ (12 × Packs across)

Target good packs: 10000 units; Common web width: 11.811023622047244 inch; Machine pitch: 3.937007874015748 inch; Packs across: 3 units; Forming web GSM: 350 g/m²; Lidding GSM: 60 g/m²; Process loss on gross input: 5 % → 95.15 lb

محسوب من مدخلاتك. أكّد المواصفات مع المورد.

المعادلة بوضوح.

Gross packs = Good target ÷ (1 − Waste fraction); Web length(ft) = Gross packs × Pitch(in) ÷ (12 × Packs across)

The result answers a specific purchasing question: Work out blister material requirement with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read total gross forming and lidding material in lb. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

كيفية استخدام هذه الحاسبة

  1. 01

    Collect Target good packs (units); Common web width (inch); Machine pitch (inch); Packs across (units); Forming web GSM (g/m²); Lidding GSM (g/m²); Process loss on gross input (%). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review total gross forming and lidding material and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

حساب يمكنك التحقق منه

For this US purchasing example, enter target good packs 10,000.00 units, common web width 11.81 inch, machine pitch 3.94 inch, packs across 3.00 units. The calculated total gross forming and lidding material is 95.15 lb. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

العدد المستهدف للعبوات المطابقة
10,000 وحدات
عرض الشريط المشترك
11.8110236 inch
خطوة الآلة
3.93700787 inch
عدد العبوات عبر العرض
3 وحدات
الوزن المساحي لشريط التشكيل
350 g/m²
الوزن المساحي لمادة الغطاء
60 g/m²
خسارة العملية على إجمالي المدخلات
5 %
Gross packs = Good target ÷ (1 − Waste fraction); Web length(ft) = Gross packs × Pitch(in) ÷ (12 × Packs across)
إجمالي مادتي التشكيل والغطاء95.15 lb

الأسئلة الشائعة

Which units should I use for blister material requirement?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two blister material requirement results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record target good packs (units), common web width (inch), machine pitch (inch), packs across (units) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

تحقق من المعادلة والوحدات والافتراضات المعروضة قبل استخدام النتيجة.

الطريقة والوحدات وافتراضات المواد ↗