Nested Trays per Carton Stack Calculator — US Units
Nested Trays per Carton Stack connects the figures on a US supplier quote with the quantity used by your packaging operation. Have internal carton height (inch), total vertical packing clearance (inch), first tray height (inch) ready before you start.
مواصفاتك
أقصى عدد للصواني في رصة واحدة داخل الكرتون
يفترض رصة عمودية واحدة لكل كرتون. يجب أن تلائم قاعدة الصينية طول الكرتون الداخلي وعرضه كلًا على حدة.
استخدم الزيادة المقاسة لكل صينية متداخلة. لا تتم نمذجة التشوه والانضغاط.
الارتفاع المفيد = الداخلي − الخلوص الرأسي الكلي؛ صواني/رصة = تقريب لأسفل((المفيد − ارتفاع الأولى) ÷ الخطوة) + 1 إذا لائمت الأولى
Internal carton height: 33.46456692913386 inch; Total vertical packing clearance: 0.39370078740157477 inch; First tray height: 1.968503937007874 inch; Additional nesting pitch: 0.31496062992125984 inch; Trays to pack: 10000 units → 99.00 traysمحسوب من مدخلاتك. أكّد المواصفات مع المورد.
المعادلة بوضوح.
The result answers a specific purchasing question: Work out nested trays per carton stack with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read maximum trays in one carton stack in trays. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.
كيفية استخدام هذه الحاسبة
- 01
Collect Internal carton height (inch); Total vertical packing clearance (inch); First tray height (inch); Additional nesting pitch (inch); Trays to pack (units). Leave optional unknown values blank rather than substituting zero.
- 02
Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.
- 03
Review maximum trays in one carton stack and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.
حساب يمكنك التحقق منه
For this US purchasing example, enter internal carton height 33.46 inch, total vertical packing clearance 0.3937 inch, first tray height 1.97 inch, additional nesting pitch 0.3150 inch. The calculated maximum trays in one carton stack is 99.00 trays. The table lists the remaining inputs and results so the scenario can be checked or reproduced.
- الارتفاع الداخلي للصندوق
- 33.4645669 inch
- إجمالي الخلوص الرأسي للتغليف
- 0.393700787 inch
- ارتفاع الصينية الأولى
- 1.96850394 inch
- خطوة التداخل الإضافية
- 0.31496063 inch
- الصواني المطلوب تعبئتها
- 10,000 وحدات
Usable height = Internal carton height − Total vertical clearance; Trays/stack = floor((Usable height − First tray height) ÷ Nesting pitch) + 1 when the first tray fitsالأسئلة الشائعة
Which units should I use for nested trays per carton stack?
Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.
Can I compare two nested trays per carton stack results directly?
Yes, when both runs use the same specification, purchasing boundary and included charges. Record internal carton height (inch), total vertical packing clearance (inch), first tray height (inch), additional nesting pitch (inch) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.
تحقق من المعادلة والوحدات والافتراضات المعروضة قبل استخدام النتيجة.
الطريقة والوحدات وافتراضات المواد ↗