Packaging Cost per Unit Calculator — US Units
Packaging Cost per Unit connects the figures on a US supplier quote with the quantity used by your packaging operation. Have web width (inch), print / pack repeat (inch), lanes across the web (lanes) ready before you start.
مواصفاتك
استخدم الوزن الفعلي لكل متر مربع من المورد أو من القياس إن توفر.
تسمية للعملة فقط. لا تحويل بسعر الصرف.
نسبة الفاقد من إجمالي المدخلات.
تكلفة المادة لكل عبوة مطابقة
الفاقد هو نسبة المادة المفقودة من إجمالي المادة. الاحتياج الإجمالي = الاحتياج الصافي ÷ (1 − معدل الفاقد).
تكلفة المادة فقط؛ لا تشمل الأدوات والشحن وعمالة التحويل والملحقات.
Cost/good unit = Width(in) × Repeat(in) ÷ 144 ÷ Lanes ÷ (1 − Waste fraction) × Price/ft²
Web width: 31.496062992125985 inch; Print / pack repeat: 9.84251968503937 inch; Lanes across the web: 2 lanes; Film GSM: 80 g/m²; Film price on selected basis: 1.3607771100000001 USD/lb; Process waste: 5 % → US$0.02526/packمحسوب من مدخلاتك. أكّد المواصفات مع المورد.
المعادلة بوضوح.
The result answers a specific purchasing question: Work out packaging cost per unit with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read material cost per good pack in your selected currency/pack. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.
كيفية استخدام هذه الحاسبة
- 01
Collect Web width (inch); Print / pack repeat (inch); Lanes across the web (lanes); Film GSM (g/m²); Film price on selected basis (currency/lb); Process waste (%). Leave optional unknown values blank rather than substituting zero.
- 02
Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.
- 03
Review material cost per good pack and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.
حساب يمكنك التحقق منه
For this US purchasing example, enter web width 31.50 inch, print / pack repeat 9.84 inch, lanes across the web 2.00 lanes, film gsm 80.00 g/m². The calculated material cost per good pack is US$0.02526/pack. The table lists the remaining inputs and results so the scenario can be checked or reproduced.
- عرض الشريط
- 31.496063 inch
- خطوة الطباعة / العبوة
- 9.84251969 inch
- المسارات عبر عرض الشريط
- 2 lanes
- وزن الغشاء لكل متر مربع
- 80 g/m²
- سعر الغشاء على الأساس المختار
- 1.36077711 USD/lb
- هدر العملية
- 5 %
Cost/good unit = Width(in) × Repeat(in) ÷ 144 ÷ Lanes ÷ (1 − Waste fraction) × Price/ft²الأسئلة الشائعة
Which units should I use for packaging cost per unit?
Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.
Can I compare two packaging cost per unit results directly?
Yes, when both runs use the same specification, purchasing boundary and included charges. Record web width (inch), print / pack repeat (inch), lanes across the web (lanes), film gsm (g/m²) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.
تحقق من المعادلة والوحدات والافتراضات المعروضة قبل استخدام النتيجة.
الطريقة والوحدات وافتراضات المواد ↗