Packaging Reorder Point Calculator — US Units
Packaging Reorder Point connects the figures on a US supplier quote with the quantity used by your packaging operation. Have average usage per day (units/day), supplier lead time (days), chosen safety stock (units) ready before you start.
مواصفاتك
مستوى المخزون لإعادة الطلب
يجب أن يستخدم الاستهلاك اليومي ومهلة التوريد أساس أيام التشغيل أو الأيام التقويمية نفسه.
يُدخل مخزون الأمان ولا يُستنتج من مستوى خدمة أو توزيع طلب.
لا يحسب كمية الطلب أو EOQ أو موثوقية المورد أو احتمال نفاد مخزون مضمونًا.
نقطة إعادة الطلب = ceil(الاستهلاك اليومي × مهلة التوريد + مخزون الأمان)
Average usage per day: 1000 units/day; Supplier lead time: 15 days; Chosen safety stock: 5000 units → 20,000.00 وحداتمحسوب من مدخلاتك. أكّد المواصفات مع المورد.
المعادلة بوضوح.
The result answers a specific purchasing question: Work out packaging reorder point with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read reorder inventory position in units. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.
كيفية استخدام هذه الحاسبة
- 01
Collect Average usage per day (units/day); Supplier lead time (days); Chosen safety stock (units). Leave optional unknown values blank rather than substituting zero.
- 02
Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.
- 03
Review reorder inventory position and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.
حساب يمكنك التحقق منه
For this US purchasing example, enter average usage per day 1,000.00 units/day, supplier lead time 15.00 days, chosen safety stock 5,000.00 units. The calculated reorder inventory position is 20,000.00 units. The table lists the remaining inputs and results so the scenario can be checked or reproduced.
- متوسط الاستهلاك اليومي
- 1,000 وحدات/day
- مهلة توريد المورد
- 15 أيام
- مخزون الأمان المختار
- 5,000 وحدات
Reorder point = ceil(Daily usage × Lead time + Safety stock)الأسئلة الشائعة
Which units should I use for packaging reorder point?
Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.
Can I compare two packaging reorder point results directly?
Yes, when both runs use the same specification, purchasing boundary and included charges. Record average usage per day (units/day), supplier lead time (days), chosen safety stock (units) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.
تحقق من المعادلة والوحدات والافتراضات المعروضة قبل استخدام النتيجة.
الطريقة والوحدات وافتراضات المواد ↗