أداة 40 / 136

Remaining Film on Roll Calculator — US Units

Remaining Film on Roll connects the figures on a US supplier quote with the quantity used by your packaging operation. Have roll outer diameter (inch), core outer diameter (inch), film thickness (mil) ready before you start.

مواصفاتك

قِس القطر الخارجي للقلب، لا قطر التجويف.

g/m²

استخدم الوزن الفعلي لكل متر مربع من المورد أو من القياس إن توفر.

تتحدّث النتائج أثناء التعديل. لا يُحفظ شيء حتى تختار الحفظ.
حساب فوري

الطول المتبقي التقديري

3,684.77 ft
المساحة المتبقية التقديرية9,671.33 ft²
الوزن المتبقي التقديري للفيلم158.47 lb

تقدير هندسي يفترض سماكة موحدة ولفًا محكمًا دون هواء محبوس. قد يختلف الطول الفعلي.

يُستخدم القطر الخارجي للقلب؛ لا يصلح قطر التجويف الاسمي بديلاً عنه.

Remaining ft = π × (Current OD(in)² − Core OD(in)²) ÷ (48 × Thickness(mil) ÷ 1,000); Area(ft²) = Remaining ft × Width(in) ÷ 12

Roll outer diameter: 13.779527559055119 inch; Core OUTER diameter: 3.543307086614173 inch; Film thickness: 3.149606299212598 mil; Web width: 31.496062992125985 inch; Film GSM: 80 g/m² → 3,684.77 ft

محسوب من مدخلاتك. أكّد المواصفات مع المورد.

المعادلة بوضوح.

Remaining ft = π × (Current OD(in)² − Core OD(in)²) ÷ (48 × Thickness(mil) ÷ 1,000); Area(ft²) = Remaining ft × Width(in) ÷ 12

The result answers a specific purchasing question: Work out remaining film on roll with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read estimated remaining length in ft. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

كيفية استخدام هذه الحاسبة

  1. 01

    Collect Roll outer diameter (inch); Core OUTER diameter (inch); Film thickness (mil); Web width (inch); Film GSM (g/m²). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review estimated remaining length and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

حساب يمكنك التحقق منه

For this US purchasing example, enter roll outer diameter 13.78 inch, core outer diameter 3.54 inch, film thickness 3.15 mil, web width 31.50 inch. The calculated estimated remaining length is 3,684.77 ft. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

القطر الخارجي للّفة
13.7795276 inch
القطر الخارجي للقلب
3.54330709 inch
سماكة الغشاء
3.1496063 مل
عرض الشريط
31.496063 inch
وزن الغشاء لكل متر مربع
80 g/m²
Remaining ft = π × (Current OD(in)² − Core OD(in)²) ÷ (48 × Thickness(mil) ÷ 1,000); Area(ft²) = Remaining ft × Width(in) ÷ 12
الطول المتبقي التقديري3,684.77 ft

الأسئلة الشائعة

Which units should I use for remaining film on roll?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two remaining film on roll results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record roll outer diameter (inch), core outer diameter (inch), film thickness (mil), web width (inch) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

تحقق من المعادلة والوحدات والافتراضات المعروضة قبل استخدام النتيجة.

الطريقة والوحدات وافتراضات المواد ↗