أداة 36 / 136

Roll Diameter from Length Calculator — US Units

Roll Diameter from Length connects the figures on a US supplier quote with the quantity used by your packaging operation. Have roll length (ft), film thickness (mil), core outer diameter (inch) ready before you start.

مواصفاتك

قِس القطر الخارجي للقلب، لا قطر التجويف.

تتحدّث النتائج أثناء التعديل. لا يُحفظ شيء حتى تختار الحفظ.
حساب فوري

القطر الخارجي التقديري للفة

13.06 inch

تقدير هندسي يفترض سماكة موحدة ولفًا محكمًا دون هواء محبوس. قد يختلف الطول الفعلي.

يُستخدم القطر الخارجي للقلب؛ لا يصلح قطر التجويف الاسمي بديلاً عنه.

Roll OD(in) = √(Core OD(in)² + 48 × Thickness(mil) ÷ 1,000 × Length(ft) ÷ π)

Roll length: 3280.839895013123 ft; Film thickness: 3.149606299212598 mil; Core OUTER diameter: 3.543307086614173 inch → 13.06 inch

محسوب من مدخلاتك. أكّد المواصفات مع المورد.

المعادلة بوضوح.

Roll OD(in) = √(Core OD(in)² + 48 × Thickness(mil) ÷ 1,000 × Length(ft) ÷ π)

The result answers a specific purchasing question: Work out roll diameter from length with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read estimated roll outer diameter in inch. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

كيفية استخدام هذه الحاسبة

  1. 01

    Collect Roll length (ft); Film thickness (mil); Core OUTER diameter (inch). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review estimated roll outer diameter and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

حساب يمكنك التحقق منه

For this US purchasing example, enter roll length 3,280.84 ft, film thickness 3.15 mil, core outer diameter 3.54 inch. The calculated estimated roll outer diameter is 13.06 inch. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

طول اللفة
3,280.8399 ft
سماكة الغشاء
3.1496063 مل
القطر الخارجي للقلب
3.54330709 inch
Roll OD(in) = √(Core OD(in)² + 48 × Thickness(mil) ÷ 1,000 × Length(ft) ÷ π)
القطر الخارجي التقديري للفة13.06 inch

الأسئلة الشائعة

Which units should I use for roll diameter from length?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two roll diameter from length results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record roll length (ft), film thickness (mil), core outer diameter (inch) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

تحقق من المعادلة والوحدات والافتراضات المعروضة قبل استخدام النتيجة.

الطريقة والوحدات وافتراضات المواد ↗