أداة 87 / 136

Shrink Sleeve Cost per Unit Calculator — US Units

Shrink Sleeve Cost per Unit connects the figures on a US supplier quote with the quantity used by your packaging operation. Have layflat width (inch), sleeve cut length (inch), film gsm (g/m²) ready before you start.

مواصفاتك

g/m²
USD/lb
%
USD/unit

تسمية للوحدة فقط. لا يتم تحويل العملات.

تتحدّث النتائج أثناء التعديل. لا يُحفظ شيء حتى تختار الحفظ.
حساب فوري

تكلفة مادة الفيلم لكل غلاف مطابق

US$0.00616/sleeve
مادة الفيلم لكل 1,000 غلاف مطابقUS$6.1579/1,000 sleeves
شاملة التحويل المدخل لكل غلافUS$0.00616/sleeve
المساحة الاسمية لفيلم الأنبوب المفتوح0.3229 ft²/sleeve
الكتلة الاسمية للفيلم لكل غلاف0.004299 lb/sleeve
حصة إجمالي الفيلم لكل غلاف مطابق0.004525 lb/sleeve
الوزن المساحي للفيلم المستخدم65.00 g/m²

العرض المسطح نصف محيط الأنبوب المفتوح، لذا تشمل المساحة الجانبين. أي تداخل إضافي للوصلة أو تشذيب للحواف خارج هذه الهندسة الاسمية.

الفاقد نسبة مفقودة من إجمالي المدخلات. الاحتياج الإجمالي = المخرجات المطابقة ÷ (1 − الفاقد/100).

رسوم الوصل والطباعة والتحويل منفصلة ما لم تُدخل.

Sleeve ft² = 2 × Layflat width(in) × Cut length(in) ÷ 144; Cost/good sleeve = Sleeve ft² × Price/ft² ÷ (1 − Waste fraction)

Layflat width: 3.937007874015748 inch; Sleeve cut length: 5.905511811023622 inch; Film GSM: 65 g/m²; Film price on selected basis: 1.3607771100000001 USD/lb; Process loss on gross input: 5 %; Additional seaming / printing / conversion per sleeve: 0 USD/unit → US$0.00616/sleeve

محسوب من مدخلاتك. أكّد المواصفات مع المورد.

المعادلة بوضوح.

Sleeve ft² = 2 × Layflat width(in) × Cut length(in) ÷ 144; Cost/good sleeve = Sleeve ft² × Price/ft² ÷ (1 − Waste fraction)

The result answers a specific purchasing question: Work out shrink sleeve cost per unit with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read film material cost per good sleeve in your selected currency/sleeve. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

كيفية استخدام هذه الحاسبة

  1. 01

    Collect Layflat width (inch); Sleeve cut length (inch); Film GSM (g/m²); Film thickness (mil); Entered film density (g/cm³); Film price on selected basis (currency/lb); Process loss on gross input (%); Additional seaming / printing / conversion per sleeve (currency/unit). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review film material cost per good sleeve and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

حساب يمكنك التحقق منه

For this US purchasing example, enter layflat width 3.94 inch, sleeve cut length 5.91 inch, film gsm 65.00 g/m², film price on selected basis US$1.3608/lb. The calculated film material cost per good sleeve is US$0.00616/sleeve. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

عرض الأنبوب المفرود مسطحًا
3.93700787 inch
طول قطع الغلاف الأنبوبي
5.90551181 inch
وزن الغشاء لكل متر مربع
65 g/m²
سعر الغشاء على الأساس المختار
1.36077711 USD/lb
خسارة العملية على إجمالي المدخلات
5 %
اللحام / الطباعة / التحويل الإضافي لكل غلاف
0 USD/الوحدة
Sleeve ft² = 2 × Layflat width(in) × Cut length(in) ÷ 144; Cost/good sleeve = Sleeve ft² × Price/ft² ÷ (1 − Waste fraction)
تكلفة مادة الفيلم لكل غلاف مطابقUS$0.00616/sleeve

الأسئلة الشائعة

Which units should I use for shrink sleeve cost per unit?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two shrink sleeve cost per unit results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record layflat width (inch), sleeve cut length (inch), film gsm (g/m²), film thickness (mil) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

تحقق من المعادلة والوحدات والافتراضات المعروضة قبل استخدام النتيجة.

الطريقة والوحدات وافتراضات المواد ↗