WERKZEUG 51 / 136

Adhesive Consumption Calculator — US Units

Adhesive Consumption connects the figures on a US supplier quote with the quantity used by your packaging operation. Have film area (ft²), dry adhesive coat weight (g/m²), adhesive solids (%) ready before you start.

Ihre Spezifikationen

g/m²
%
Ergebnisse werden beim Bearbeiten aktualisiert. Gespeichert wird erst auf Ihre Anweisung.
Laufende Berechnung

Benötigter Nassklebstoff

11,02 lb
Verbleibender Trockenklebstoff4,41 lb
Nassauftragsgewicht5,00 g/m²

Der Feststoffanteil ist massebezogen. Dies ist der theoretische Verbrauch vor Beschichtungs-, Misch- oder Reinigungsverlusten.

Dry lb = Area(ft²) × Dry GSM × 0.0002048161436; Wet lb = Dry lb ÷ Solids fraction

Film area: 10763.910416709721 ft²; Dry adhesive coat weight: 2 g/m²; Adhesive solids: 40 % → 11,02 lb

Aus Ihren Eingaben berechnet. Bestätigen Sie die Spezifikationen mit Ihrem Lieferanten.

Die Formel verständlich erklärt.

Dry lb = Area(ft²) × Dry GSM × 0.0002048161436; Wet lb = Dry lb ÷ Solids fraction

The result answers a specific purchasing question: Work out adhesive consumption with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read wet adhesive required in lb. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

So verwenden Sie diesen Rechner

  1. 01

    Collect Film area (ft²); Dry adhesive coat weight (g/m²); Adhesive solids (%). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review wet adhesive required and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

Eine überprüfbare Berechnung

For this US purchasing example, enter film area 10,763.91 ft², dry adhesive coat weight 2.00 g/m², adhesive solids 40.00 %. The calculated wet adhesive required is 11.02 lb. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

Folienfläche
10.763,9104 ft²
Trockenauftragsgewicht des Klebstoffs
2 g/m²
Klebstoff-Feststoffgehalt
40 %
Dry lb = Area(ft²) × Dry GSM × 0.0002048161436; Wet lb = Dry lb ÷ Solids fraction
Benötigter Nassklebstoff11,02 lb

Häufige Fragen

Which units should I use for adhesive consumption?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two adhesive consumption results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record film area (ft²), dry adhesive coat weight (g/m²), adhesive solids (%) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

Prüfen Sie die angezeigte Formel, die Einheiten und die Annahmen, bevor Sie das Ergebnis verwenden.

Methode, Einheiten und Materialannahmen ↗