WERKZEUG 82 / 136

Labels per Roll Calculator — US Units

Labels per Roll connects the figures on a US supplier quote with the quantity used by your packaging operation. Have usable roll length (ft), label pitch including gap (inch), labels across (units) ready before you start.

Ihre Spezifikationen

Stück
Ergebnisse werden beim Bearbeiten aktualisiert. Gespeichert wird erst auf Ihre Anweisung.
Laufende Berechnung

Vollständige Etiketten je Rolle

10.000,00 labels
Durch vollständige Reihen belegte Länge3.280,84 ft
Nicht nutzbare Restlänge unterhalb eines Takts0,00 ft

Verwenden Sie die nutzbare Rollenlänge nach Abzug von Vor- und Nachlauf. Der Takt umfasst Etikett und Lücke in Maschinenrichtung.

Labels = floor(Usable length(ft) × 12 ÷ Label pitch(in)) × Labels across

Usable roll length: 3280.839895013123 ft; Label pitch including gap: 3.937007874015748 inch; Labels across: 1 units → 10.000,00 labels

Aus Ihren Eingaben berechnet. Bestätigen Sie die Spezifikationen mit Ihrem Lieferanten.

Die Formel verständlich erklärt.

Labels = floor(Usable length(ft) × 12 ÷ Label pitch(in)) × Labels across

The result answers a specific purchasing question: Work out labels per roll with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read complete labels per roll in labels. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

So verwenden Sie diesen Rechner

  1. 01

    Collect Usable roll length (ft); Label pitch including gap (inch); Labels across (units). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review complete labels per roll and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

Eine überprüfbare Berechnung

For this US purchasing example, enter usable roll length 3,280.84 ft, label pitch including gap 3.94 inch, labels across 1.00 units. The calculated complete labels per roll is 10,000.00 labels. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

Nutzbare Rollenlänge
3.280,8399 ft
Etikettenteilung einschließlich Lücke
3,93700787 inch
Etiketten nebeneinander
1 Stück
Labels = floor(Usable length(ft) × 12 ÷ Label pitch(in)) × Labels across
Vollständige Etiketten je Rolle10.000,00 labels

Häufige Fragen

Which units should I use for labels per roll?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two labels per roll results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record usable roll length (ft), label pitch including gap (inch), labels across (units) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

Prüfen Sie die angezeigte Formel, die Einheiten und die Annahmen, bevor Sie das Ergebnis verwenden.

Methode, Einheiten und Materialannahmen ↗