Material Required for Order Calculator — US Units
Material Required for Order connects the figures on a US supplier quote with the quantity used by your packaging operation. Have target good finished units (units), web width (inch), print / pack repeat (inch) ready before you start.
Ihre Spezifikationen
Verwenden Sie nach Möglichkeit das tatsächliche Flächengewicht des Lieferanten oder einen Messwert.
Verlustanteil am Bruttoeinsatz.
Benötigte Bruttofolie
Ausschuss ist der verlorene Anteil des Bruttomaterials. Bruttobedarf = Nettobedarf ÷ (1 − Ausschussrate).
Bahnbreite und Rapport müssen die tatsächliche Produktionszuteilung umfassen. Zusätzlicher fester Einrichtausschuss ist separat einzuplanen.
Gross pack equivalents = Good target ÷ (1 − Waste fraction); Length(ft) = Gross pack equivalents × Repeat(in) ÷ (12 × Lanes); Area(ft²) = Length(ft) × Width(in) ÷ 12
Target good finished units: 100000 units; Web width: 31.496062992125985 inch; Print / pack repeat: 9.84251968503937 inch; Lanes across the web: 2 lanes; Film GSM: 80 g/m²; Process waste: 5 % → 1.856,52 lbAus Ihren Eingaben berechnet. Bestätigen Sie die Spezifikationen mit Ihrem Lieferanten.
Die Formel verständlich erklärt.
The result answers a specific purchasing question: Work out material required for order with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read gross film required in lb. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.
So verwenden Sie diesen Rechner
- 01
Collect Target good finished units (units); Web width (inch); Print / pack repeat (inch); Lanes across the web (lanes); Film GSM (g/m²); Process waste (%). Leave optional unknown values blank rather than substituting zero.
- 02
Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.
- 03
Review gross film required and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.
Eine überprüfbare Berechnung
For this US purchasing example, enter target good finished units 100,000.00 units, web width 31.50 inch, print / pack repeat 9.84 inch, lanes across the web 2.00 lanes. The calculated gross film required is 1,856.52 lb. The table lists the remaining inputs and results so the scenario can be checked or reproduced.
- Zielzahl guter Fertigeinheiten
- 100.000 Stück
- Bahnbreite
- 31,496063 inch
- Druck- / Verpackungsrapport
- 9,84251969 inch
- Bahnen nebeneinander
- 2 lanes
- Flächengewicht der Folie
- 80 g/m²
- Prozessverlust
- 5 %
Gross pack equivalents = Good target ÷ (1 − Waste fraction); Length(ft) = Gross pack equivalents × Repeat(in) ÷ (12 × Lanes); Area(ft²) = Length(ft) × Width(in) ÷ 12Häufige Fragen
Which units should I use for material required for order?
Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.
Can I compare two material required for order results directly?
Yes, when both runs use the same specification, purchasing boundary and included charges. Record target good finished units (units), web width (inch), print / pack repeat (inch), lanes across the web (lanes) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.
Prüfen Sie die angezeigte Formel, die Einheiten und die Annahmen, bevor Sie das Ergebnis verwenden.
Methode, Einheiten und Materialannahmen ↗