WERKZEUG 34 / 136

Roll Length from Weight Calculator — US Units

Roll Length from Weight connects the figures on a US supplier quote with the quantity used by your packaging operation. Have net film weight (lb), web width (inch), film gsm (g/m²) ready before you start.

Ihre Spezifikationen

g/m²

Verwenden Sie nach Möglichkeit das tatsächliche Flächengewicht des Lieferanten oder einen Messwert.

Ergebnisse werden beim Bearbeiten aktualisiert. Gespeichert wird erst auf Ihre Anweisung.
Laufende Berechnung

Lauflänge der Rolle

4.101,05 ft
Folienfläche10.763,91 ft²

Ziehen Sie Hülsen- und Umhüllungsgewicht ab, bevor Sie das Nettofoliengewicht eingeben.

Length(ft) = Net lb ÷ (Width(in) ÷ 12 × GSM × 0.0002048161436)

Net film weight: 176.36980974790205 lb; Web width: 31.496062992125985 inch; Film GSM: 80 g/m² → 4.101,05 ft

Aus Ihren Eingaben berechnet. Bestätigen Sie die Spezifikationen mit Ihrem Lieferanten.

Die Formel verständlich erklärt.

Length(ft) = Net lb ÷ (Width(in) ÷ 12 × GSM × 0.0002048161436)

The result answers a specific purchasing question: Work out roll length from weight with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read roll running length in ft. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

So verwenden Sie diesen Rechner

  1. 01

    Collect Net film weight (lb); Web width (inch); Film GSM (g/m²). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review roll running length and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

Eine überprüfbare Berechnung

For this US purchasing example, enter net film weight 176.37 lb, web width 31.50 inch, film gsm 80.00 g/m². The calculated roll running length is 4,101.05 ft. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

Nettofoliengewicht
176,36981 lb
Bahnbreite
31,496063 inch
Flächengewicht der Folie
80 g/m²
Length(ft) = Net lb ÷ (Width(in) ÷ 12 × GSM × 0.0002048161436)
Lauflänge der Rolle4.101,05 ft

Häufige Fragen

Which units should I use for roll length from weight?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two roll length from weight results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record net film weight (lb), web width (inch), film gsm (g/m²) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

Prüfen Sie die angezeigte Formel, die Einheiten und die Annahmen, bevor Sie das Ergebnis verwenden.

Methode, Einheiten und Materialannahmen ↗