HERRAMIENTA 81 / 136

Carton Tooling Amortization Calculator — US Units

Carton Tooling Amortization connects the figures on a US supplier quote with the quantity used by your packaging operation. Have cutting die (currency), printing plates (currency), foil tooling (currency) ready before you start.

Tus especificaciones

USD
USD
USD
USD
USD
unidades

Solo etiqueta de unidad. Sin conversión de divisas.

Los resultados se actualizan al editar. No se guarda nada hasta que tú lo decidas.
Cálculo en tiempo real

Coste por cartón

US$0,00180/carton
Coste por 1.000 cartonesUS$1,8000/1,000 carton
Total de utillaje y preparaciónUS$1800,00

Supone que se fabrica la cantidad de vida útil introducida. No incluye utillaje de reemplazo posterior.

Utillaje/unidad = (Troquel + Planchas + Herramienta de estampación + Herramienta de relieve + Otra preparación) ÷ Cantidad de reparto

Cutting die: 1200 USD; Printing plates: 600 USD; Foil tooling: 0 USD; Embossing tooling: 0 USD; Other setup: 0 USD; Expected lifetime cartons: 1000000 units → US$0,00180/carton

Calculado con tus datos. Confirma las especificaciones con tu proveedor.

La fórmula, explicada.

Utillaje/unidad = (Troquel + Planchas + Herramienta de estampación + Herramienta de relieve + Otra preparación) ÷ Cantidad de reparto

The result answers a specific purchasing question: Work out carton tooling amortization with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read cost per carton in your selected currency/carton. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

Cómo usar esta calculadora

  1. 01

    Collect Cutting die (currency); Printing plates (currency); Foil tooling (currency); Embossing tooling (currency); Other setup (currency); Expected lifetime cartons (units). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review cost per carton and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

Un cálculo que puedes comprobar

For this US purchasing example, enter cutting die US$1,200.00, printing plates US$600.00, foil tooling US$0.00000, embossing tooling US$0.00000. The calculated cost per carton is US$0.00180/carton. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

Troquel de corte
1200 USD
Planchas de impresión
600 USD
Utillaje de estampación con lámina
0 USD
Utillaje de relieve
0 USD
Otra preparación
0 USD
Estuches previstos durante la vida útil
1.000.000 unidades
Tooling/unit = (Die + Plates + Foil tooling + Embossing tooling + Other setup) ÷ Allocation quantity
Coste por cartónUS$0,00180/carton

Preguntas frecuentes

Which units should I use for carton tooling amortization?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two carton tooling amortization results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record cutting die (currency), printing plates (currency), foil tooling (currency), embossing tooling (currency) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

Comprueba la fórmula, las unidades y los supuestos mostrados antes de utilizar el resultado.

Método, unidades y supuestos del material ↗