HERRAMIENTA 78 / 136

Folding Carton Board Requirement Calculator — US Units

Folding Carton Board Requirement connects the figures on a US supplier quote with the quantity used by your packaging operation. Have good cartons required (units), actual blank width (inch), actual blank length (inch) ready before you start.

Tus especificaciones

unidades
g/m²
%
Los resultados se actualizan al editar. No se guarda nada hasta que tú lo decidas.
Cálculo en tiempo real

Superficie bruta de recortes necesaria

22.660,86 ft²
Material bruto de recortes necesario1392,39 lb

Usa las dimensiones reales del recorte. Las dimensiones interiores o exteriores del envase terminado no definen un recorte de troquel exacto.

La merma es la fracción perdida de la entrada bruta. Necesidad bruta = producción conforme ÷ (1 − merma/100).

La compra opcional de hojas añade recortes rectangulares sobrantes a la necesidad bruta de piezas.

Compara solo dos orientaciones rectangulares uniformes. Excluye separaciones, márgenes de pinza, restricciones de fibra y anidado irregular de troqueles.

Gross ft² = Good carton target × Blank ft² ÷ (1 − Waste fraction); Board lb = Gross ft² × GSM × 0.0002048161436

Good cartons required: 10000 units; Actual blank width: 19.68503937007874 inch; Actual blank length: 15.748031496062993 inch; Board GSM: 300 g/m²; Process loss on gross input: 5 %; Sheet width (optional): inch; Sheet length (optional): inch → 22.660,86 ft²

Calculado con tus datos. Confirma las especificaciones con tu proveedor.

La fórmula, explicada.

Gross ft² = Good carton target × Blank ft² ÷ (1 − Waste fraction); Board lb = Gross ft² × GSM × 0.0002048161436

The result answers a specific purchasing question: Work out folding carton board requirement with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read gross blank area required in ft². Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

Cómo usar esta calculadora

  1. 01

    Collect Good cartons required (units); Actual blank width (inch); Actual blank length (inch); Board GSM (g/m²); Process loss on gross input (%); Sheet width (optional) (inch); Sheet length (optional) (inch). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review gross blank area required and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

Un cálculo que puedes comprobar

For this US purchasing example, enter good cartons required 10,000.00 units, actual blank width 19.69 inch, actual blank length 15.75 inch, board gsm 300.00 g/m². The calculated gross blank area required is 22,660.86 ft². The table lists the remaining inputs and results so the scenario can be checked or reproduced.

Estuches válidos necesarios
10.000 unidades
Ancho real del desarrollo
19,6850394 inch
Longitud real del desarrollo
15,7480315 inch
Gramaje del cartón
300 g/m²
Pérdida sobre entrada bruta
5 %
Ancho de pliego (opcional)
inch
Longitud de pliego (opcional)
inch
Gross ft² = Good carton target × Blank ft² ÷ (1 − Waste fraction); Board lb = Gross ft² × GSM × 0.0002048161436
Superficie bruta de recortes necesaria22.660,86 ft²

Preguntas frecuentes

Which units should I use for folding carton board requirement?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two folding carton board requirement results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record good cartons required (units), actual blank width (inch), actual blank length (inch), board gsm (g/m²) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

Comprueba la fórmula, las unidades y los supuestos mostrados antes de utilizar el resultado.

Método, unidades y supuestos del material ↗