HERRAMIENTA 40 / 136

Remaining Film on Roll Calculator — US Units

Remaining Film on Roll connects the figures on a US supplier quote with the quantity used by your packaging operation. Have roll outer diameter (inch), core outer diameter (inch), film thickness (mil) ready before you start.

Tus especificaciones

Mida el exterior del mandril, no su diámetro interior.

g/m²

Usa el gramaje del proveedor o el medido, si está disponible.

Los resultados se actualizan al editar. No se guarda nada hasta que tú lo decidas.
Cálculo en tiempo real

Longitud restante estimada

3684,77 ft
Superficie restante estimada9671,33 ft²
Peso restante estimado de la película158,47 lb

Estimación geométrica: supone espesor uniforme, bobinado compacto y ausencia de aire atrapado. La longitud real puede variar.

Se utiliza el diámetro EXTERIOR del mandril; el diámetro interior nominal no lo sustituye.

Remaining ft = π × (Current OD(in)² − Core OD(in)²) ÷ (48 × Thickness(mil) ÷ 1,000); Area(ft²) = Remaining ft × Width(in) ÷ 12

Roll outer diameter: 13.779527559055119 inch; Core OUTER diameter: 3.543307086614173 inch; Film thickness: 3.149606299212598 mil; Web width: 31.496062992125985 inch; Film GSM: 80 g/m² → 3684,77 ft

Calculado con tus datos. Confirma las especificaciones con tu proveedor.

La fórmula, explicada.

Remaining ft = π × (Current OD(in)² − Core OD(in)²) ÷ (48 × Thickness(mil) ÷ 1,000); Area(ft²) = Remaining ft × Width(in) ÷ 12

The result answers a specific purchasing question: Work out remaining film on roll with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read estimated remaining length in ft. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

Cómo usar esta calculadora

  1. 01

    Collect Roll outer diameter (inch); Core OUTER diameter (inch); Film thickness (mil); Web width (inch); Film GSM (g/m²). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review estimated remaining length and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

Un cálculo que puedes comprobar

For this US purchasing example, enter roll outer diameter 13.78 inch, core outer diameter 3.54 inch, film thickness 3.15 mil, web width 31.50 inch. The calculated estimated remaining length is 3,684.77 ft. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

Diámetro exterior de bobina
13,7795276 inch
Diámetro EXTERIOR del mandril
3,54330709 inch
Espesor del film
3,1496063 mil
Ancho de banda
31,496063 inch
Gramaje del film
80 g/m²
Remaining ft = π × (Current OD(in)² − Core OD(in)²) ÷ (48 × Thickness(mil) ÷ 1,000); Area(ft²) = Remaining ft × Width(in) ÷ 12
Longitud restante estimada3684,77 ft

Preguntas frecuentes

Which units should I use for remaining film on roll?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two remaining film on roll results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record roll outer diameter (inch), core outer diameter (inch), film thickness (mil), web width (inch) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

Comprueba la fórmula, las unidades y los supuestos mostrados antes de utilizar el resultado.

Método, unidades y supuestos del material ↗