OUTIL 121 / 136

Blister Material Requirement Calculator — US Units

Blister Material Requirement connects the figures on a US supplier quote with the quantity used by your packaging operation. Have target good packs (units), common web width (inch), machine pitch (inch) ready before you start.

Vos spécifications

unités
unités
g/m²
g/m²
%
Les résultats s’actualisent pendant la saisie. Rien n’est enregistré sans votre choix.
Calcul en direct

Total brut des matières de formage et d’operculage

95,15 lb
Longueur déroulée brute par bande1 151,17 ft
Matière brute de formage81,22 lb
Matière brute d’operculage13,92 lb
Surface brute de chaque bande1 133,04 ft²

La perte est une fraction de l’apport brut. Besoin brut = production conforme ÷ (1 − perte/100).

Ce modèle suppose des largeurs et pas identiques pour le formage et l’operculage. Ajoutez séparément les pertes fixes de démarrage ; les besoins sont continus, sans arrondi aux cycles machine complets.

Gross packs = Good target ÷ (1 − Waste fraction); Web length(ft) = Gross packs × Pitch(in) ÷ (12 × Packs across)

Target good packs: 10000 units; Common web width: 11.811023622047244 inch; Machine pitch: 3.937007874015748 inch; Packs across: 3 units; Forming web GSM: 350 g/m²; Lidding GSM: 60 g/m²; Process loss on gross input: 5 % → 95,15 lb

Calculé à partir de vos données. Confirmez les spécifications avec votre fournisseur.

La formule expliquée.

Gross packs = Good target ÷ (1 − Waste fraction); Web length(ft) = Gross packs × Pitch(in) ÷ (12 × Packs across)

The result answers a specific purchasing question: Work out blister material requirement with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read total gross forming and lidding material in lb. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

Comment utiliser ce calculateur

  1. 01

    Collect Target good packs (units); Common web width (inch); Machine pitch (inch); Packs across (units); Forming web GSM (g/m²); Lidding GSM (g/m²); Process loss on gross input (%). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review total gross forming and lidding material and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

Un calcul que vous pouvez vérifier

For this US purchasing example, enter target good packs 10,000.00 units, common web width 11.81 inch, machine pitch 3.94 inch, packs across 3.00 units. The calculated total gross forming and lidding material is 95.15 lb. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

Objectif d’emballages conformes
10 000 unités
Largeur commune de bande
11,8110236 inch
Pas machine
3,93700787 inch
Emballages dans la largeur
3 unités
Grammage de la bande de formage
350 g/m²
Grammage de l’opercule
60 g/m²
Pertes sur l’entrée brute
5 %
Gross packs = Good target ÷ (1 − Waste fraction); Web length(ft) = Gross packs × Pitch(in) ÷ (12 × Packs across)
Total brut des matières de formage et d’operculage95,15 lb

Questions fréquentes

Which units should I use for blister material requirement?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two blister material requirement results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record target good packs (units), common web width (inch), machine pitch (inch), packs across (units) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

Vérifiez la formule, les unités et les hypothèses affichées avant d’utiliser le résultat.

Méthode, unités et hypothèses sur les matériaux ↗