OUTIL 123 / 136

FIBC Bag Volume & Dimensions Calculator — US Units

FIBC Bag Volume & Dimensions connects the figures on a US supplier quote with the quantity used by your packaging operation. Have internal filled length (inch), internal filled width (inch), internal filling height (inch) ready before you start.

Vos spécifications

Les résultats s’actualisent pendant la saisie. Rien n’est enregistré sans votre choix.
Calcul en direct

Volume intérieur théorique

34,33 ft³
Volume intérieur théorique en litres256,78 US gal
Hauteur intérieure de remplissage nécessaire47,24 inch

Géométrie intérieure remplie rectangulaire uniquement. Bombement, tassement, doublures, coutures et espace libre peuvent modifier le volume utile.

Estime le volume et la hauteur de remplissage, pas les dimensions de coupe du tissu ni la charge de travail sûre. Confirmez séparément la spécification du fournisseur.

Volume(ft³) = Length(in) × Width(in) × Filling height(in) ÷ 1,728; Required height(in) = Payload(lb) ÷ Density(lb/ft³) ÷ Base area(ft²) × 12

Internal filled length: 35.43307086614173 inch; Internal filled width: 35.43307086614173 inch; Internal filling height: 47.24409448818898 inch → 34,33 ft³

Calculé à partir de vos données. Confirmez les spécifications avec votre fournisseur.

La formule expliquée.

Volume(ft³) = Length(in) × Width(in) × Filling height(in) ÷ 1,728; Required height(in) = Payload(lb) ÷ Density(lb/ft³) ÷ Base area(ft²) × 12

The result answers a specific purchasing question: Work out fibc bag volume & dimensions with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read theoretical internal volume in ft³. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

Comment utiliser ce calculateur

  1. 01

    Collect Internal filled length (inch); Internal filled width (inch); Internal filling height (inch); Target product mass (lb); Product bulk density (lb/ft³). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review theoretical internal volume and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

Un calcul que vous pouvez vérifier

For this US purchasing example, enter internal filled length 35.43 inch, internal filled width 35.43 inch, internal filling height 47.24 inch. The calculated theoretical internal volume is 34.33 ft³. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

Longueur intérieure remplie
35,4330709 inch
Largeur intérieure remplie
35,4330709 inch
Hauteur intérieure de remplissage
47,2440945 inch
Volume(ft³) = Length(in) × Width(in) × Filling height(in) ÷ 1,728; Required height(in) = Payload(lb) ÷ Density(lb/ft³) ÷ Base area(ft²) × 12
Volume intérieur théorique34,33 ft³

Questions fréquentes

Which units should I use for fibc bag volume & dimensions?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two fibc bag volume & dimensions results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record internal filled length (inch), internal filled width (inch), internal filling height (inch), target product mass (lb) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

Vérifiez la formule, les unités et les hypothèses affichées avant d’utiliser le résultat.

Méthode, unités et hypothèses sur les matériaux ↗