OUTIL 78 / 136

Folding Carton Board Requirement Calculator — US Units

Folding Carton Board Requirement connects the figures on a US supplier quote with the quantity used by your packaging operation. Have good cartons required (units), actual blank width (inch), actual blank length (inch) ready before you start.

Vos spécifications

unités
g/m²
%
Les résultats s’actualisent pendant la saisie. Rien n’est enregistré sans votre choix.
Calcul en direct

Surface brute de flans nécessaire

22 660,86 ft²
Matière brute des flans nécessaire1 392,39 lb

Utilise les dimensions réelles du flan. Les dimensions intérieures ou extérieures de l’emballage fini ne définissent pas un flan de découpe exact.

La perte est une fraction de l’apport brut. Besoin brut = production conforme ÷ (1 − perte/100).

L’achat facultatif en feuilles ajoute les chutes rectangulaires au besoin brut en flans.

Compare uniquement deux orientations rectangulaires uniformes. Exclut espaces, marges de pince, contraintes du sens des fibres et imbrication de formes irrégulières.

Gross ft² = Good carton target × Blank ft² ÷ (1 − Waste fraction); Board lb = Gross ft² × GSM × 0.0002048161436

Good cartons required: 10000 units; Actual blank width: 19.68503937007874 inch; Actual blank length: 15.748031496062993 inch; Board GSM: 300 g/m²; Process loss on gross input: 5 %; Sheet width (optional): inch; Sheet length (optional): inch → 22 660,86 ft²

Calculé à partir de vos données. Confirmez les spécifications avec votre fournisseur.

La formule expliquée.

Gross ft² = Good carton target × Blank ft² ÷ (1 − Waste fraction); Board lb = Gross ft² × GSM × 0.0002048161436

The result answers a specific purchasing question: Work out folding carton board requirement with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read gross blank area required in ft². Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

Comment utiliser ce calculateur

  1. 01

    Collect Good cartons required (units); Actual blank width (inch); Actual blank length (inch); Board GSM (g/m²); Process loss on gross input (%); Sheet width (optional) (inch); Sheet length (optional) (inch). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review gross blank area required and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

Un calcul que vous pouvez vérifier

For this US purchasing example, enter good cartons required 10,000.00 units, actual blank width 19.69 inch, actual blank length 15.75 inch, board gsm 300.00 g/m². The calculated gross blank area required is 22,660.86 ft². The table lists the remaining inputs and results so the scenario can be checked or reproduced.

Étuis conformes requis
10 000 unités
Largeur réelle du flan
19,6850394 inch
Longueur réelle du flan
15,7480315 inch
Grammage du carton
300 g/m²
Pertes sur l’entrée brute
5 %
Largeur de feuille (facultative)
inch
Longueur de feuille (facultative)
inch
Gross ft² = Good carton target × Blank ft² ÷ (1 − Waste fraction); Board lb = Gross ft² × GSM × 0.0002048161436
Surface brute de flans nécessaire22 660,86 ft²

Questions fréquentes

Which units should I use for folding carton board requirement?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two folding carton board requirement results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record good cartons required (units), actual blank width (inch), actual blank length (inch), board gsm (g/m²) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

Vérifiez la formule, les unités et les hypothèses affichées avant d’utiliser le résultat.

Méthode, unités et hypothèses sur les matériaux ↗