OUTIL 57 / 136

Material Required for Order Calculator — US Units

Material Required for Order connects the figures on a US supplier quote with the quantity used by your packaging operation. Have target good finished units (units), web width (inch), print / pack repeat (inch) ready before you start.

Vos spécifications

unités
lanes
g/m²

Utilisez le grammage réel du fournisseur ou une mesure, si disponible.

%

Pourcentage perdu de l’apport brut.

Les résultats s’actualisent pendant la saisie. Rien n’est enregistré sans votre choix.
Calcul en direct

Film brut nécessaire

1 856,52 lb
Surface brute de film nécessaire113 304,32 ft²
Longueur déroulée brute nécessaire43 168,95 ft
Équivalent en unités brutes105 263,16 unités

Le taux de perte est le pourcentage de matière brute perdu. Besoin brut = besoin net ÷ (1 − taux de perte).

La largeur et le pas doivent inclure l’allocation réelle de production. Les pertes fixes supplémentaires de réglage doivent être prévues séparément.

Gross pack equivalents = Good target ÷ (1 − Waste fraction); Length(ft) = Gross pack equivalents × Repeat(in) ÷ (12 × Lanes); Area(ft²) = Length(ft) × Width(in) ÷ 12

Target good finished units: 100000 units; Web width: 31.496062992125985 inch; Print / pack repeat: 9.84251968503937 inch; Lanes across the web: 2 lanes; Film GSM: 80 g/m²; Process waste: 5 % → 1 856,52 lb

Calculé à partir de vos données. Confirmez les spécifications avec votre fournisseur.

La formule expliquée.

Gross pack equivalents = Good target ÷ (1 − Waste fraction); Length(ft) = Gross pack equivalents × Repeat(in) ÷ (12 × Lanes); Area(ft²) = Length(ft) × Width(in) ÷ 12

The result answers a specific purchasing question: Work out material required for order with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read gross film required in lb. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

Comment utiliser ce calculateur

  1. 01

    Collect Target good finished units (units); Web width (inch); Print / pack repeat (inch); Lanes across the web (lanes); Film GSM (g/m²); Process waste (%). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review gross film required and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

Un calcul que vous pouvez vérifier

For this US purchasing example, enter target good finished units 100,000.00 units, web width 31.50 inch, print / pack repeat 9.84 inch, lanes across the web 2.00 lanes. The calculated gross film required is 1,856.52 lb. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

Objectif d’unités finies conformes
100 000 unités
Largeur de bande
31,496063 inch
Pas d’impression / emballage
9,84251969 inch
Pistes dans la largeur
2 lanes
Grammage du film
80 g/m²
Pertes de procédé
5 %
Gross pack equivalents = Good target ÷ (1 − Waste fraction); Length(ft) = Gross pack equivalents × Repeat(in) ÷ (12 × Lanes); Area(ft²) = Length(ft) × Width(in) ÷ 12
Film brut nécessaire1 856,52 lb

Questions fréquentes

Which units should I use for material required for order?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two material required for order results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record target good finished units (units), web width (inch), print / pack repeat (inch), lanes across the web (lanes) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

Vérifiez la formule, les unités et les hypothèses affichées avant d’utiliser le résultat.

Méthode, unités et hypothèses sur les matériaux ↗