Metal Can Landed Cost Calculator — US Units
Metal Can Landed Cost connects the figures on a US supplier quote with the quantity used by your packaging operation. Have quoted can body price (currency/unit), total material quote (currency), end / lid price per can (currency/unit) ready before you start.
Vos spécifications
Libellé d’unité uniquement. Aucune conversion de devise.
Coût par boîte
Les montants proposés et tous les frais utilisent la devise choisie sans conversion de change.
N’ajoutez pas à nouveau transport ou composants si le devis les inclut déjà. Les droits sont un montant monétaire saisi.
Coût rendu/boîte = Prix boîte + Prix fond séparé + (Transport + Outillage + Autres frais fixes) ÷ Quantité
Quoted can body price: 0.2 USD/unit; End / lid price per can: 0.04 USD/unit; Order quantity: 10000 units; Freight for this order: 250 USD; Tooling allocated to this order: 0 USD; Customs / duty amount: 0 USD; Other fixed order charges: 0 USD → US$0,2650/canCalculé à partir de vos données. Confirmez les spécifications avec votre fournisseur.
La formule expliquée.
The result answers a specific purchasing question: Work out metal can landed cost with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read cost per can in your selected currency/can. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.
Comment utiliser ce calculateur
- 01
Collect Quoted can body price (currency/unit); Total material quote (currency); End / lid price per can (currency/unit); Order quantity (units); Freight for this order (currency); Tooling allocated to this order (currency); Customs / duty amount (currency); Other fixed order charges (currency). Leave optional unknown values blank rather than substituting zero.
- 02
Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.
- 03
Review cost per can and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.
Un calcul que vous pouvez vérifier
For this US purchasing example, enter quoted can body price US$0.2000/unit, end / lid price per can US$0.04000/unit, order quantity 10,000.00 units, freight for this order US$250.00. The calculated cost per can is US$0.2650/can. The table lists the remaining inputs and results so the scenario can be checked or reproduced.
- Prix proposé du corps de boîte
- 0,2 USD/unité
- Prix du fond ou du couvercle par boîte
- 0,04 USD/unité
- Quantité commandée
- 10 000 unités
- Transport de cette commande
- 250 USD
- Outillage affecté à cette commande
- 0 USD
- Montant des droits de douane
- 0 USD
- Autres frais fixes de commande
- 0 USD
Landed/can = Can price + Separate end price + (Freight + Tooling + Other fixed charges) ÷ QuantityQuestions fréquentes
Which units should I use for metal can landed cost?
Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.
Can I compare two metal can landed cost results directly?
Yes, when both runs use the same specification, purchasing boundary and included charges. Record quoted can body price (currency/unit), total material quote (currency), end / lid price per can (currency/unit), order quantity (units) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.
Vérifiez la formule, les unités et les hypothèses affichées avant d’utiliser le résultat.
Méthode, unités et hypothèses sur les matériaux ↗