Shrink Sleeve Cost per Unit Calculator — US Units
Shrink Sleeve Cost per Unit connects the figures on a US supplier quote with the quantity used by your packaging operation. Have layflat width (inch), sleeve cut length (inch), film gsm (g/m²) ready before you start.
Vos spécifications
Libellé d’unité uniquement. Aucune conversion de devise.
Coût de film par manchon conforme
La largeur à plat est la moitié de la circonférence du tube ouvert, donc la surface inclut les deux faces. Tout chevauchement ou rognage supplémentaire est hors de cette géométrie nominale.
La perte est une fraction de l’apport brut. Besoin brut = production conforme ÷ (1 − perte/100).
Les frais de soudure, d’impression et de transformation sont distincts sauf saisie.
Sleeve ft² = 2 × Layflat width(in) × Cut length(in) ÷ 144; Cost/good sleeve = Sleeve ft² × Price/ft² ÷ (1 − Waste fraction)
Layflat width: 3.937007874015748 inch; Sleeve cut length: 5.905511811023622 inch; Film GSM: 65 g/m²; Film price on selected basis: 1.3607771100000001 USD/lb; Process loss on gross input: 5 %; Additional seaming / printing / conversion per sleeve: 0 USD/unit → US$0,00616/sleeveCalculé à partir de vos données. Confirmez les spécifications avec votre fournisseur.
La formule expliquée.
The result answers a specific purchasing question: Work out shrink sleeve cost per unit with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read film material cost per good sleeve in your selected currency/sleeve. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.
Comment utiliser ce calculateur
- 01
Collect Layflat width (inch); Sleeve cut length (inch); Film GSM (g/m²); Film thickness (mil); Entered film density (g/cm³); Film price on selected basis (currency/lb); Process loss on gross input (%); Additional seaming / printing / conversion per sleeve (currency/unit). Leave optional unknown values blank rather than substituting zero.
- 02
Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.
- 03
Review film material cost per good sleeve and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.
Un calcul que vous pouvez vérifier
For this US purchasing example, enter layflat width 3.94 inch, sleeve cut length 5.91 inch, film gsm 65.00 g/m², film price on selected basis US$1.3608/lb. The calculated film material cost per good sleeve is US$0.00616/sleeve. The table lists the remaining inputs and results so the scenario can be checked or reproduced.
- Largeur à plat du tube
- 3,93700787 inch
- Longueur de coupe du manchon
- 5,90551181 inch
- Grammage du film
- 65 g/m²
- Prix du film sur la base choisie
- 1,36077711 USD/lb
- Pertes sur l’entrée brute
- 5 %
- Soudure / impression / transformation supplémentaires par manchon
- 0 USD/unité
Sleeve ft² = 2 × Layflat width(in) × Cut length(in) ÷ 144; Cost/good sleeve = Sleeve ft² × Price/ft² ÷ (1 − Waste fraction)Questions fréquentes
Which units should I use for shrink sleeve cost per unit?
Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.
Can I compare two shrink sleeve cost per unit results directly?
Yes, when both runs use the same specification, purchasing boundary and included charges. Record layflat width (inch), sleeve cut length (inch), film gsm (g/m²), film thickness (mil) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.
Vérifiez la formule, les unités et les hypothèses affichées avant d’utiliser le résultat.
Méthode, unités et hypothèses sur les matériaux ↗