Blister Material Requirement Calculator — US Units
Blister Material Requirement connects the figures on a US supplier quote with the quantity used by your packaging operation. Have target good packs (units), common web width (inch), machine pitch (inch) ready before you start.
आपके विनिर्देश
फॉर्मिंग और लिडिंग की कुल सकल सामग्री
अपव्यय सकल इनपुट का खोया अंश है। सकल आवश्यकता = स्वीकृत उत्पादन ÷ (1 − अपव्यय/100)।
यह नियोजन मॉडल फॉर्मिंग और लिडिंग वेब की चौड़ाई तथा पिच समान मानता है। स्थिर शुरुआती हानि अलग जोड़ें; आवश्यकता निरंतर सकल सामग्री है, पूरी मशीन साइकिल तक पूर्णांकन नहीं।
Gross packs = Good target ÷ (1 − Waste fraction); Web length(ft) = Gross packs × Pitch(in) ÷ (12 × Packs across)
Target good packs: 10000 units; Common web width: 11.811023622047244 inch; Machine pitch: 3.937007874015748 inch; Packs across: 3 units; Forming web GSM: 350 g/m²; Lidding GSM: 60 g/m²; Process loss on gross input: 5 % → 95.15 lbआपके इनपुट से गणना की गई है। आपूर्तिकर्ता से विनिर्देशों की पुष्टि करें।
सूत्र का स्पष्ट विवरण।
The result answers a specific purchasing question: Work out blister material requirement with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read total gross forming and lidding material in lb. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.
इस कैलकुलेटर का उपयोग कैसे करें
- 01
Collect Target good packs (units); Common web width (inch); Machine pitch (inch); Packs across (units); Forming web GSM (g/m²); Lidding GSM (g/m²); Process loss on gross input (%). Leave optional unknown values blank rather than substituting zero.
- 02
Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.
- 03
Review total gross forming and lidding material and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.
ऐसी गणना जिसे आप जाँच सकते हैं
For this US purchasing example, enter target good packs 10,000.00 units, common web width 11.81 inch, machine pitch 3.94 inch, packs across 3.00 units. The calculated total gross forming and lidding material is 95.15 lb. The table lists the remaining inputs and results so the scenario can be checked or reproduced.
- लक्षित स्वीकृत पैकों की संख्या
- 10,000 इकाइयाँ
- साझा वेब चौड़ाई
- 11.8110236 inch
- मशीन पिच
- 3.93700787 inch
- चौड़ाई में पैकों की संख्या
- 3 इकाइयाँ
- फॉर्मिंग वेब का जीएसएम
- 350 g/m²
- लिडिंग का जीएसएम
- 60 g/m²
- सकल इनपुट पर प्रक्रिया हानि
- 5 %
Gross packs = Good target ÷ (1 − Waste fraction); Web length(ft) = Gross packs × Pitch(in) ÷ (12 × Packs across)अक्सर पूछे जाने वाले प्रश्न
Which units should I use for blister material requirement?
Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.
Can I compare two blister material requirement results directly?
Yes, when both runs use the same specification, purchasing boundary and included charges. Record target good packs (units), common web width (inch), machine pitch (inch), packs across (units) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.
परिणाम का उपयोग करने से पहले दिखाई गई गणना का सूत्र, इकाइयाँ और मान्यताएँ जाँचें।
विधि, इकाइयाँ और सामग्री की मान्यताएँ ↗