Thermoformed Part Material Weight Calculator — US Units
Thermoformed Part Material Weight connects the figures on a US supplier quote with the quantity used by your packaging operation. Have web width (inch), machine pitch (inch), parts across (units) ready before you start.
आपके विनिर्देश
प्रति भाग सकल शीट सामग्री आवंटन
यह सकल वेब आवंटन है, तैयार भाग का वज़न नहीं। अंतर में स्केलेटन कतरन और रखे गए भाग के बाहर की सामग्री शामिल है।
दर्ज पिच पर मशीन दिशा में भागों की एक पंक्ति मानी गई है; उस रिपीट की चौड़ाई में सभी कैविटी शामिल करें।
Gross lb/part = Web width(in) × Pitch(in) ÷ (144 × Parts across) × Sheet GSM × 0.0002048161436
Web width: 31.496062992125985 inch; Machine pitch: 11.811023622047244 inch; Parts across: 4 units; Sheet GSM: 600 g/m² → 0.0794 lb/partआपके इनपुट से गणना की गई है। आपूर्तिकर्ता से विनिर्देशों की पुष्टि करें।
सूत्र का स्पष्ट विवरण।
The result answers a specific purchasing question: Work out thermoformed part material weight with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read gross sheet material allocation per part in lb/part. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.
इस कैलकुलेटर का उपयोग कैसे करें
- 01
Collect Web width (inch); Machine pitch (inch); Parts across (units); Sheet GSM (g/m²). Leave optional unknown values blank rather than substituting zero.
- 02
Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.
- 03
Review gross sheet material allocation per part and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.
ऐसी गणना जिसे आप जाँच सकते हैं
For this US purchasing example, enter web width 31.50 inch, machine pitch 11.81 inch, parts across 4.00 units, sheet gsm 600.00 g/m². The calculated gross sheet material allocation per part is 0.0794 lb/part. The table lists the remaining inputs and results so the scenario can be checked or reproduced.
- वेब की चौड़ाई
- 31.496063 inch
- मशीन पिच
- 11.8110236 inch
- चौड़ाई में भाग
- 4 इकाइयाँ
- शीट का ग्राम प्रति वर्ग मीटर भार
- 600 g/m²
Gross lb/part = Web width(in) × Pitch(in) ÷ (144 × Parts across) × Sheet GSM × 0.0002048161436अक्सर पूछे जाने वाले प्रश्न
Which units should I use for thermoformed part material weight?
Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.
Can I compare two thermoformed part material weight results directly?
Yes, when both runs use the same specification, purchasing boundary and included charges. Record web width (inch), machine pitch (inch), parts across (units), sheet gsm (g/m²) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.
परिणाम का उपयोग करने से पहले दिखाई गई गणना का सूत्र, इकाइयाँ और मान्यताएँ जाँचें।
विधि, इकाइयाँ और सामग्री की मान्यताएँ ↗