STRUMENTO 121 / 136

Blister Material Requirement Calculator — US Units

Blister Material Requirement connects the figures on a US supplier quote with the quantity used by your packaging operation. Have target good packs (units), common web width (inch), machine pitch (inch) ready before you start.

Le tue specifiche

unità
unità
g/m²
g/m²
%
I risultati si aggiornano mentre modifichi i dati. Nulla viene salvato finché non lo scegli.
Calcolo in tempo reale

Totale lordo dei materiali di formatura e chiusura

95,15 lb
Lunghezza svolta lorda per nastro1151,17 ft
Materiale lordo di formatura81,22 lb
Materiale lordo di chiusura13,92 lb
Area lorda di ciascun nastro1133,04 ft²

Lo scarto è la frazione persa dell’input lordo. Fabbisogno lordo = output conforme ÷ (1 − scarto/100).

Questo modello presume larghezze e passi uguali per formatura e chiusura. Aggiungi separatamente perdite fisse di avviamento; il fabbisogno è materiale lordo continuo, senza arrotondamento a cicli macchina completi.

Gross packs = Good target ÷ (1 − Waste fraction); Web length(ft) = Gross packs × Pitch(in) ÷ (12 × Packs across)

Target good packs: 10000 units; Common web width: 11.811023622047244 inch; Machine pitch: 3.937007874015748 inch; Packs across: 3 units; Forming web GSM: 350 g/m²; Lidding GSM: 60 g/m²; Process loss on gross input: 5 % → 95,15 lb

Calcolato dai tuoi dati. Conferma le specifiche con il fornitore.

La formula spiegata.

Gross packs = Good target ÷ (1 − Waste fraction); Web length(ft) = Gross packs × Pitch(in) ÷ (12 × Packs across)

The result answers a specific purchasing question: Work out blister material requirement with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read total gross forming and lidding material in lb. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

Come usare questo calcolatore

  1. 01

    Collect Target good packs (units); Common web width (inch); Machine pitch (inch); Packs across (units); Forming web GSM (g/m²); Lidding GSM (g/m²); Process loss on gross input (%). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review total gross forming and lidding material and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

Un calcolo che puoi verificare

For this US purchasing example, enter target good packs 10,000.00 units, common web width 11.81 inch, machine pitch 3.94 inch, packs across 3.00 units. The calculated total gross forming and lidding material is 95.15 lb. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

Obiettivo di confezioni conformi
10.000 unità
Larghezza comune del nastro
11,8110236 inch
Passo macchina
3,93700787 inch
Confezioni in larghezza
3 unità
Grammatura del nastro di formatura
350 g/m²
Grammatura del materiale di chiusura
60 g/m²
Perdita sull’input lordo
5 %
Gross packs = Good target ÷ (1 − Waste fraction); Web length(ft) = Gross packs × Pitch(in) ÷ (12 × Packs across)
Totale lordo dei materiali di formatura e chiusura95,15 lb

Domande frequenti

Which units should I use for blister material requirement?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two blister material requirement results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record target good packs (units), common web width (inch), machine pitch (inch), packs across (units) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

Verifica la formula, le unità e le ipotesi visualizzate prima di utilizzare il risultato.

Metodo, unità e ipotesi sui materiali ↗