STRUMENTO 38 / 136

Roll Diameter from Weight Calculator — US Units

Roll Diameter from Weight connects the figures on a US supplier quote with the quantity used by your packaging operation. Have net film weight (lb), web width (inch), film gsm (g/m²) ready before you start.

Le tue specifiche

g/m²

Usa la grammatura effettiva del fornitore o misurata, se disponibile.

Misura l’esterno dell’anima, non il foro interno.

I risultati si aggiornano mentre modifichi i dati. Nulla viene salvato finché non lo scegli.
Calcolo in tempo reale

Diametro esterno stimato della bobina

14,49 inch
Lunghezza svolta calcolata4101,05 ft

Stima geometrica: presuppone spessore uniforme, avvolgimento compatto e assenza di aria intrappolata. La lunghezza effettiva può variare.

Si usa il diametro ESTERNO dell’anima; il foro nominale non è un sostituto.

Length(ft) = Net lb ÷ (Width(in) ÷ 12 × GSM × 0.0002048161436); OD(in) = √(Core(in)² + 48 × Thickness(mil) ÷ 1,000 × Length(ft) ÷ π)

Net film weight: 176.36980974790205 lb; Web width: 31.496062992125985 inch; Film GSM: 80 g/m²; Film thickness: 3.149606299212598 mil; Core OUTER diameter: 3.543307086614173 inch → 14,49 inch

Calcolato dai tuoi dati. Conferma le specifiche con il fornitore.

La formula spiegata.

Length(ft) = Net lb ÷ (Width(in) ÷ 12 × GSM × 0.0002048161436); OD(in) = √(Core(in)² + 48 × Thickness(mil) ÷ 1,000 × Length(ft) ÷ π)

The result answers a specific purchasing question: Work out roll diameter from weight with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read estimated roll outer diameter in inch. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

Come usare questo calcolatore

  1. 01

    Collect Net film weight (lb); Web width (inch); Film GSM (g/m²); Film thickness (mil); Core OUTER diameter (inch). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review estimated roll outer diameter and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

Un calcolo che puoi verificare

For this US purchasing example, enter net film weight 176.37 lb, web width 31.50 inch, film gsm 80.00 g/m², film thickness 3.15 mil. The calculated estimated roll outer diameter is 14.49 inch. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

Peso netto del film
176,36981 lb
Larghezza del nastro
31,496063 inch
Grammatura del film
80 g/m²
Spessore del film
3,1496063 mil
Diametro ESTERNO dell’anima
3,54330709 inch
Length(ft) = Net lb ÷ (Width(in) ÷ 12 × GSM × 0.0002048161436); OD(in) = √(Core(in)² + 48 × Thickness(mil) ÷ 1,000 × Length(ft) ÷ π)
Diametro esterno stimato della bobina14,49 inch

Domande frequenti

Which units should I use for roll diameter from weight?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two roll diameter from weight results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record net film weight (lb), web width (inch), film gsm (g/m²), film thickness (mil) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

Verifica la formula, le unità e le ipotesi visualizzate prima di utilizzare il risultato.

Metodo, unità e ipotesi sui materiali ↗