STRUMENTO 94 / 136

Thermoformed Part Material Weight Calculator — US Units

Thermoformed Part Material Weight connects the figures on a US supplier quote with the quantity used by your packaging operation. Have web width (inch), machine pitch (inch), parts across (units) ready before you start.

Le tue specifiche

unità
g/m²
I risultati si aggiornano mentre modifichi i dati. Nulla viene salvato finché non lo scegli.
Calcolo in tempo reale

Quota di materiale lordo in foglio per pezzo

0,0794 lb/part
Area lorda del nastro per pezzo0,6458 ft²/part
Quota lorda per 1.000 pezzi79,37 lb/1,000 parts

È un’allocazione lorda del nastro, non il peso del pezzo finito. La differenza include lo scheletro di sfrido e il materiale fuori dal pezzo trattenuto.

Presuppone una fila di pezzi in direzione macchina per passo inserito; includi tutte le cavità trasversali di quel passo.

Gross lb/part = Web width(in) × Pitch(in) ÷ (144 × Parts across) × Sheet GSM × 0.0002048161436

Web width: 31.496062992125985 inch; Machine pitch: 11.811023622047244 inch; Parts across: 4 units; Sheet GSM: 600 g/m² → 0,0794 lb/part

Calcolato dai tuoi dati. Conferma le specifiche con il fornitore.

La formula spiegata.

Gross lb/part = Web width(in) × Pitch(in) ÷ (144 × Parts across) × Sheet GSM × 0.0002048161436

The result answers a specific purchasing question: Work out thermoformed part material weight with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read gross sheet material allocation per part in lb/part. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

Come usare questo calcolatore

  1. 01

    Collect Web width (inch); Machine pitch (inch); Parts across (units); Sheet GSM (g/m²). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review gross sheet material allocation per part and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

Un calcolo che puoi verificare

For this US purchasing example, enter web width 31.50 inch, machine pitch 11.81 inch, parts across 4.00 units, sheet gsm 600.00 g/m². The calculated gross sheet material allocation per part is 0.0794 lb/part. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

Larghezza del nastro
31,496063 inch
Passo macchina
11,8110236 inch
Pezzi affiancati
4 unità
Grammatura della lastra
600 g/m²
Gross lb/part = Web width(in) × Pitch(in) ÷ (144 × Parts across) × Sheet GSM × 0.0002048161436
Quota di materiale lordo in foglio per pezzo0,0794 lb/part

Domande frequenti

Which units should I use for thermoformed part material weight?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two thermoformed part material weight results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record web width (inch), machine pitch (inch), parts across (units), sheet gsm (g/m²) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

Verifica la formula, le unità e le ipotesi visualizzate prima di utilizzare il risultato.

Metodo, unità e ipotesi sui materiali ↗