도구 47 / 136

3-Ply Laminate GSM Calculator — US Units

3-Ply Laminate GSM connects the figures on a US supplier quote with the quantity used by your packaging operation. Build the structure or component list from the supplied specification.

필름 3개 층, 접착 계면 2개.

예시 불러오기

대표 밀도입니다. 실제 밀도는 수지 등급과 배합에 따라 달라지므로 가능한 경우 공급업체 자료나 실측값을 사용하세요. 실측 또는 공급업체 평량이 일반적으로 밀도 추정보다 신뢰도가 높습니다. 사용자 지정 재료에는 검증된 밀도를 입력하세요. 일반 밀도로 종이 평량을 추정하지 마세요.

FILM LAYER 01
16.68g/m²

Estimated using typical PET / BOPET density of 1.39 g/cm³.

FILM LAYER 02
24.30g/m²

Estimated using typical 알루미늄 포일 density of 2.70 g/cm³.

FILM LAYER 03
55.20g/m²

Estimated using typical PE(일반) density of 0.9200 g/cm³.

접착제, 인쇄 및 코팅

제외할 첨가재는 0을 입력하세요. 모든 평량은 m²당 잔류 건조 질량입니다. 접착제, 잉크 및 코팅 두께를 평량으로 추정하지 않습니다.

Adhesive interface 1

잔류 건조 도포량

Adhesive interface 2

잔류 건조 도포량

잉크

잔류 건조 질량

코팅

잔류 건조 질량

기타 잔류 재료

잔류 건조 질량

라미네이트 총평량100.18g / m²
필름 층
96.18 g/m²
접착제, 잉크, 코팅 및 기타
4.00 g/m²
라미네이트 단위 질량당 면적
48.74 ft²/lb
필름 두께만
3.19 mil
1,000m²당 중량
220.86 lb
각 층과 첨가재의 질량 기여도
층 / 첨가재건조 평량
1. PET / BOPET16.68
2. 알루미늄 포일24.30
3. PE(일반)55.20
Adhesive interface 12.00
Adhesive interface 22.00
잉크 · 제외됨0.00
코팅 · 제외됨0.00
기타 잔류 재료 · 제외됨0.00
합계100.18

필름 두께는 접착제, 잉크 및 코팅 두께를 제외합니다. 수율은 공정 손실 전 이론값입니다. 이 추정에는 재료 라이브러리의 대표 밀도가 포함됩니다.

공식 및 대입값

Layer GSM = Thickness(mil) × 25.4 × Density(g/cm³). Total GSM includes dry retained additions.

Yield(ft²/lb) = 4,882.427636 ÷ Total GSM. Material $/ft² = GSM × 0.0002048161436 × Material $/lb.

PET / BOPET: 0.4724 mil × 25.4 × 1.39 = 16.68 g/m²

알루미늄 포일: 0.3543 mil × 25.4 × 2.70 = 24.30 g/m²

PE(일반): 2.36 mil × 25.4 × 0.9200 = 55.20 g/m²

Total retained basis weight: 100.18 g/m²

Yield: 4,882.427636 ÷ 100.18 = 48.74 ft²/lb

계산식을 알기 쉽게.

3-ply GSM = 25.4 × Σ(Three mil thicknesses × Their densities) + Dry retained additions

Build 3-ply laminate gsm from the actual layer or component records rather than a generic material assumption. Enter dimensional specifications in the displayed US units and keep every price paired with its stated denominator. Review the layer contributions and the finished result together before comparing suppliers.

계산기 사용 방법

  1. 01

    Choose the actual materials or components and record their quantities, prices and retained additions.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review each contribution, then compare the total at the same production quantity and cost boundary.

검증할 수 있는 계산

The worked US scenario below keeps the supplied components, cost boundary and physical quantities explicit. Its dollar prices are illustrative, independent of the interactive example.

This independent 3-ply example has a 0.5-mil PET face at 1.39 g/cm³ and 2 PE layers at 1 mil and 0.92 g/cm³ each. Every interface adds 2 dry GSM of adhesive.

PET price
$2/lb
PE price
$1.25/lb
Wet adhesive
$2/lb · 40% solids
Total basis weight
68.39 g/m²
Coverage yield
71.39 ft²/lb
Material cost
US$0.02329/ft²
Layer GSM = mil × 25.4 × density; Yield(ft²/lb) = 4,882.427636 ÷ Total GSM

These are theoretical material figures. Converting loss, labor, energy and freight are excluded. Dry adhesive is retained mass; its purchased wet mass is divided by 0.40.

자주 묻는 질문

Which units should I use for 3-ply laminate gsm?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two 3-ply laminate gsm results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record the component structure and cost basis for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

결과를 사용하기 전에 표시된 공식, 단위 및 가정을 확인하세요.

계산 방법, 단위 및 재료 가정 ↗