Roll Weight from Diameter Calculator — US Units
Roll Weight from Diameter connects the figures on a US supplier quote with the quantity used by your packaging operation. Have roll outer diameter (inch), core outer diameter (inch), film thickness (mil) ready before you start.
사양 입력
지관의 내경이 아닌 외경을 측정하세요.
공급업체의 실제 평량 또는 실측 평량이 있으면 사용하세요.
필름 예상 순중량
두께가 균일하고 단단히 감겼으며 공기층이 없다고 가정한 기하학적 추정입니다. 실제 원단 길이는 다를 수 있습니다.
지관 외경을 사용하며 공칭 내경으로 대신할 수 없습니다.
Length(ft) = π × (OD(in)² − Core(in)²) ÷ (48 × Thickness(mil) ÷ 1,000); Net lb = Length(ft) × Width(in) ÷ 12 × GSM × 0.0002048161436
Roll outer diameter: 13.779527559055119 inch; Core OUTER diameter: 3.543307086614173 inch; Film thickness: 3.149606299212598 mil; Web width: 31.496062992125985 inch; Film GSM: 80 g/m² → 158.47 lb입력한 값으로 계산했습니다. 공급업체에 사양을 확인하세요.
계산식을 알기 쉽게.
The result answers a specific purchasing question: Work out roll weight from diameter with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read estimated net film weight in lb. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.
계산기 사용 방법
- 01
Collect Roll outer diameter (inch); Core OUTER diameter (inch); Film thickness (mil); Web width (inch); Film GSM (g/m²). Leave optional unknown values blank rather than substituting zero.
- 02
Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.
- 03
Review estimated net film weight and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.
검증할 수 있는 계산
For this US purchasing example, enter roll outer diameter 13.78 inch, core outer diameter 3.54 inch, film thickness 3.15 mil, web width 31.50 inch. The calculated estimated net film weight is 158.47 lb. The table lists the remaining inputs and results so the scenario can be checked or reproduced.
- 롤 외경
- 13.7795276 inch
- 지관 외경
- 3.54330709 inch
- 필름 두께
- 3.1496063 밀
- 원단 폭
- 31.496063 inch
- 필름 평량
- 80 g/m²
Length(ft) = π × (OD(in)² − Core(in)²) ÷ (48 × Thickness(mil) ÷ 1,000); Net lb = Length(ft) × Width(in) ÷ 12 × GSM × 0.0002048161436자주 묻는 질문
Which units should I use for roll weight from diameter?
Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.
Can I compare two roll weight from diameter results directly?
Yes, when both runs use the same specification, purchasing boundary and included charges. Record roll outer diameter (inch), core outer diameter (inch), film thickness (mil), web width (inch) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.
결과를 사용하기 전에 표시된 공식, 단위 및 가정을 확인하세요.
계산 방법, 단위 및 재료 가정 ↗