FERRAMENTA 121 / 136

Blister Material Requirement Calculator — US Units

Blister Material Requirement connects the figures on a US supplier quote with the quantity used by your packaging operation. Have target good packs (units), common web width (inch), machine pitch (inch) ready before you start.

As suas especificações

unidades
unidades
g/m²
g/m²
%
Os resultados atualizam-se ao editar. Nada é guardado até decidir fazê-lo.
Cálculo em tempo real

Total bruto dos materiais de formação e selagem

95,15 lb
Comprimento linear bruto por banda1.151,17 ft
Material bruto de formação81,22 lb
Material bruto de selagem13,92 lb
Área bruta de cada banda1.133,04 ft²

A perda é a fração perdida da entrada bruta. Necessidade bruta = produção conforme ÷ (1 − perda/100).

Este modelo pressupõe larguras e passos iguais de formação e selagem. Adicione perdas fixas de arranque separadamente; as necessidades são de material bruto contínuo, sem arredondar a ciclos completos.

Gross packs = Good target ÷ (1 − Waste fraction); Web length(ft) = Gross packs × Pitch(in) ÷ (12 × Packs across)

Target good packs: 10000 units; Common web width: 11.811023622047244 inch; Machine pitch: 3.937007874015748 inch; Packs across: 3 units; Forming web GSM: 350 g/m²; Lidding GSM: 60 g/m²; Process loss on gross input: 5 % → 95,15 lb

Calculado a partir dos seus dados. Confirme as especificações com o fornecedor.

A fórmula explicada.

Gross packs = Good target ÷ (1 − Waste fraction); Web length(ft) = Gross packs × Pitch(in) ÷ (12 × Packs across)

The result answers a specific purchasing question: Work out blister material requirement with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read total gross forming and lidding material in lb. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

Como utilizar esta calculadora

  1. 01

    Collect Target good packs (units); Common web width (inch); Machine pitch (inch); Packs across (units); Forming web GSM (g/m²); Lidding GSM (g/m²); Process loss on gross input (%). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review total gross forming and lidding material and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

Um cálculo que pode verificar

For this US purchasing example, enter target good packs 10,000.00 units, common web width 11.81 inch, machine pitch 3.94 inch, packs across 3.00 units. The calculated total gross forming and lidding material is 95.15 lb. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

Quantidade pretendida de embalagens conformes
10.000 unidades
Largura comum da banda
11,8110236 inch
Passo da máquina
3,93700787 inch
Embalagens na largura
3 unidades
Gramagem da banda de formação
350 g/m²
Gramagem do material de selagem
60 g/m²
Perda sobre a entrada bruta
5 %
Gross packs = Good target ÷ (1 − Waste fraction); Web length(ft) = Gross packs × Pitch(in) ÷ (12 × Packs across)
Total bruto dos materiais de formação e selagem95,15 lb

Perguntas frequentes

Which units should I use for blister material requirement?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two blister material requirement results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record target good packs (units), common web width (inch), machine pitch (inch), packs across (units) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

Verifique a fórmula, as unidades e os pressupostos apresentados antes de utilizar o resultado.

Método, unidades e pressupostos dos materiais ↗