FERRAMENTA 71 / 136

Boxes per Corrugated Sheet Calculator — US Units

Boxes per Corrugated Sheet connects the figures on a US supplier quote with the quantity used by your packaging operation. Have sheet width (inch), sheet length (inch), actual blank width (inch) ready before you start.

As suas especificações

Os resultados atualizam-se ao editar. Nada é guardado até decidir fazê-lo.
Cálculo em tempo real

Melhor disposição retangular simples

4,00 blanks/sheet
Disposição do recorte sem rotação4,00 blanks/sheet
Recorte rodado 90°3,00 blanks/sheet
Aproveitamento da área retangular83,33 %

Compara apenas duas orientações retangulares uniformes. Exclui intervalos, margens de pinça, restrições do sentido da fibra e encaixe irregular de corte e vinco.

Rendimento = arredondar para baixo(Largura folha ÷ Largura molde) × arredondar para baixo(Comprimento folha ÷ Comprimento molde)

Sheet width: 47.24409448818898 inch; Sheet length: 31.496062992125985 inch; Actual blank width: 19.68503937007874 inch; Actual blank length: 15.748031496062993 inch → 4,00 blanks/sheet

Calculado a partir dos seus dados. Confirme as especificações com o fornecedor.

A fórmula explicada.

Rendimento = arredondar para baixo(Largura folha ÷ Largura molde) × arredondar para baixo(Comprimento folha ÷ Comprimento molde)

The result answers a specific purchasing question: Work out boxes per corrugated sheet with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read best simple rectangular layout in blanks/sheet. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

Como utilizar esta calculadora

  1. 01

    Collect Sheet width (inch); Sheet length (inch); Actual blank width (inch); Actual blank length (inch). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review best simple rectangular layout and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

Um cálculo que pode verificar

For this US purchasing example, enter sheet width 47.24 inch, sheet length 31.50 inch, actual blank width 19.69 inch, actual blank length 15.75 inch. The calculated best simple rectangular layout is 4.00 blanks/sheet. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

Largura da folha
47,2440945 inch
Comprimento da folha
31,496063 inch
Largura real do molde
19,6850394 inch
Comprimento real do molde
15,7480315 inch
Yield = floor(Sheet width ÷ Blank width) × floor(Sheet length ÷ Blank length)
Melhor disposição retangular simples4,00 blanks/sheet

Perguntas frequentes

Which units should I use for boxes per corrugated sheet?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two boxes per corrugated sheet results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record sheet width (inch), sheet length (inch), actual blank width (inch), actual blank length (inch) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

Verifique a fórmula, as unidades e os pressupostos apresentados antes de utilizar o resultado.

Método, unidades e pressupostos dos materiais ↗