Cost per 1,000 Packs Calculator — US Units
Cost per 1,000 Packs connects the figures on a US supplier quote with the quantity used by your packaging operation. Have web width (inch), print / pack repeat (inch), lanes across the web (lanes) ready before you start.
As suas especificações
Utilize a gramagem real do fornecedor ou medida, quando disponível.
Apenas identifica a moeda. Sem conversão cambial.
Percentagem perdida da entrada bruta.
Custo de material por 1.000 embalagens conformes
A perda é a percentagem de material bruto perdido. Necessidade bruta = necessidade líquida ÷ (1 − taxa de perda).
Apenas custo do material; exclui ferramentas, transporte, mão de obra de transformação e acessórios.
Cost/1,000 good packs = Area/pack(ft²) × 1,000 ÷ (1 − Waste fraction) × Price/ft²
Web width: 31.496062992125985 inch; Print / pack repeat: 9.84251968503937 inch; Lanes across the web: 2 lanes; Film GSM: 80 g/m²; Film price on selected basis: 1.3607771100000001 USD/lb; Process waste: 5 % → US$25,26/1,000 packsCalculado a partir dos seus dados. Confirme as especificações com o fornecedor.
A fórmula explicada.
The result answers a specific purchasing question: Work out cost per 1,000 packs with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read material cost per 1,000 good packs in your selected currency/1,000 packs. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.
Como utilizar esta calculadora
- 01
Collect Web width (inch); Print / pack repeat (inch); Lanes across the web (lanes); Film GSM (g/m²); Film price on selected basis (currency/lb); Process waste (%). Leave optional unknown values blank rather than substituting zero.
- 02
Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.
- 03
Review material cost per 1,000 good packs and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.
Um cálculo que pode verificar
For this US purchasing example, enter web width 31.50 inch, print / pack repeat 9.84 inch, lanes across the web 2.00 lanes, film gsm 80.00 g/m². The calculated material cost per 1,000 good packs is US$25.26/1,000 packs. The table lists the remaining inputs and results so the scenario can be checked or reproduced.
- Largura da banda
- 31,496063 inch
- Repetição de impressão / embalagem
- 9,84251969 inch
- Vias na largura da banda
- 2 lanes
- Gramagem do filme
- 80 g/m²
- Preço do filme na base escolhida
- 1,36077711 USD/lb
- Desperdício do processo
- 5 %
Cost/1,000 good packs = Area/pack(ft²) × 1,000 ÷ (1 − Waste fraction) × Price/ft²Perguntas frequentes
Which units should I use for cost per 1,000 packs?
Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.
Can I compare two cost per 1,000 packs results directly?
Yes, when both runs use the same specification, purchasing boundary and included charges. Record web width (inch), print / pack repeat (inch), lanes across the web (lanes), film gsm (g/m²) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.
Verifique a fórmula, as unidades e os pressupostos apresentados antes de utilizar o resultado.
Método, unidades e pressupostos dos materiais ↗