FERRAMENTA 40 / 136

Remaining Film on Roll Calculator — US Units

Remaining Film on Roll connects the figures on a US supplier quote with the quantity used by your packaging operation. Have roll outer diameter (inch), core outer diameter (inch), film thickness (mil) ready before you start.

As suas especificações

Meça o exterior do mandril, não o seu furo.

g/m²

Utilize a gramagem real do fornecedor ou medida, quando disponível.

Os resultados atualizam-se ao editar. Nada é guardado até decidir fazê-lo.
Cálculo em tempo real

Comprimento restante estimado

3.684,77 ft
Área restante estimada9.671,33 ft²
Peso restante estimado do filme158,47 lb

Estimativa geométrica: pressupõe espessura uniforme, enrolamento apertado e ausência de ar retido. O comprimento real pode variar.

Utiliza-se o diâmetro EXTERIOR do mandril; o furo nominal não o substitui.

Remaining ft = π × (Current OD(in)² − Core OD(in)²) ÷ (48 × Thickness(mil) ÷ 1,000); Area(ft²) = Remaining ft × Width(in) ÷ 12

Roll outer diameter: 13.779527559055119 inch; Core OUTER diameter: 3.543307086614173 inch; Film thickness: 3.149606299212598 mil; Web width: 31.496062992125985 inch; Film GSM: 80 g/m² → 3.684,77 ft

Calculado a partir dos seus dados. Confirme as especificações com o fornecedor.

A fórmula explicada.

Remaining ft = π × (Current OD(in)² − Core OD(in)²) ÷ (48 × Thickness(mil) ÷ 1,000); Area(ft²) = Remaining ft × Width(in) ÷ 12

The result answers a specific purchasing question: Work out remaining film on roll with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read estimated remaining length in ft. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

Como utilizar esta calculadora

  1. 01

    Collect Roll outer diameter (inch); Core OUTER diameter (inch); Film thickness (mil); Web width (inch); Film GSM (g/m²). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review estimated remaining length and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

Um cálculo que pode verificar

For this US purchasing example, enter roll outer diameter 13.78 inch, core outer diameter 3.54 inch, film thickness 3.15 mil, web width 31.50 inch. The calculated estimated remaining length is 3,684.77 ft. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

Diâmetro exterior do rolo
13,7795276 inch
Diâmetro EXTERIOR do núcleo
3,54330709 inch
Espessura do filme
3,1496063 mil
Largura da banda
31,496063 inch
Gramagem do filme
80 g/m²
Remaining ft = π × (Current OD(in)² − Core OD(in)²) ÷ (48 × Thickness(mil) ÷ 1,000); Area(ft²) = Remaining ft × Width(in) ÷ 12
Comprimento restante estimado3.684,77 ft

Perguntas frequentes

Which units should I use for remaining film on roll?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two remaining film on roll results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record roll outer diameter (inch), core outer diameter (inch), film thickness (mil), web width (inch) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

Verifique a fórmula, as unidades e os pressupostos apresentados antes de utilizar o resultado.

Método, unidades e pressupostos dos materiais ↗