ИНСТРУМЕНТ 83 / 136

Label Roll Length from Count Calculator — US Units

Label Roll Length from Count connects the figures on a US supplier quote with the quantity used by your packaging operation. Have required label count (units), label pitch including gap (inch), labels across (units) ready before you start.

Ваши параметры

шт.
шт.
Результаты обновляются при изменении данных. Расчёт сохраняется только по вашему выбору.
Расчёт в реальном времени

Минимальная длина полотна для полных рядов

3 280,84 ft
Требуемое количество полных рядов10 000,00 rows
Дополнительные этикетки в последнем ряду0,00 labels

Округляет вверх до полных рядов. Начальные и конечные участки, припуски на склейки и технологические отходы добавляйте отдельно.

Required rows = ceil(Label count ÷ Labels across); Length(ft) = Rows × Pitch(in) ÷ 12

Required label count: 10000 units; Label pitch including gap: 3.937007874015748 inch; Labels across: 1 units → 3 280,84 ft

Рассчитано по вашим данным. Подтвердите параметры у поставщика.

Понятное объяснение формулы.

Required rows = ceil(Label count ÷ Labels across); Length(ft) = Rows × Pitch(in) ÷ 12

The result answers a specific purchasing question: Work out label roll length from count with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read minimum complete-row web length in ft. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

Как пользоваться калькулятором

  1. 01

    Collect Required label count (units); Label pitch including gap (inch); Labels across (units). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review minimum complete-row web length and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

Расчёт, который можно проверить

For this US purchasing example, enter required label count 10,000.00 units, label pitch including gap 3.94 inch, labels across 1.00 units. The calculated minimum complete-row web length is 3,280.84 ft. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

Требуемое число этикеток
10 000 шт.
Шаг этикетки с зазором
3,93700787 inch
Этикетки по ширине
1 шт.
Required rows = ceil(Label count ÷ Labels across); Length(ft) = Rows × Pitch(in) ÷ 12
Минимальная длина полотна для полных рядов3 280,84 ft

Частые вопросы

Which units should I use for label roll length from count?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two label roll length from count results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record required label count (units), label pitch including gap (inch), labels across (units) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

Перед использованием результата проверьте показанную формулу, единицы измерения и допущения.

Методика, единицы и допущения о материале ↗