ИНСТРУМЕНТ 63 / 136

Molded Fiber Tooling Amortization Calculator — US Units

Molded Fiber Tooling Amortization connects the figures on a US supplier quote with the quantity used by your packaging operation. Have mold / die cost (currency), initial setup cost (currency), expected lifetime items (units) ready before you start.

Ваши параметры

USD
USD
шт.

Только обозначение единицы. Без конвертации валют.

Результаты обновляются при изменении данных. Расчёт сохраняется только по вашему выбору.
Расчёт в реальном времени

Стоимость одного изделия

US$0,02000/шт.
Стоимость 1 000 изделийUS$20,00/1,000 item
Общие затраты на форму и первоначальную настройкуUS$2 000,00

Выпуск за срок службы — плановое допущение. Замена форм и повторная настройка не учитываются, если они не включены во введённую сумму.

Не добавляйте это распределение повторно, если оснастка уже включена в цену лотка.

Оснастка на изделие = (Форма или штамп + Первая настройка) ÷ Ожидаемый выпуск за срок использования; Оснастка на 1 000 = Оснастка на изделие × 1 000

Mold / die cost: 1500 USD; Initial setup cost: 500 USD; Expected lifetime items: 100000 units → US$0,02000/шт.

Рассчитано по вашим данным. Подтвердите параметры у поставщика.

Понятное объяснение формулы.

Оснастка на изделие = (Форма или штамп + Первая настройка) ÷ Ожидаемый выпуск за срок использования; Оснастка на 1 000 = Оснастка на изделие × 1 000

The result answers a specific purchasing question: Work out molded fiber tooling amortization with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read cost per item in your selected currency/item. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

Как пользоваться калькулятором

  1. 01

    Collect Mold / die cost (currency); Initial setup cost (currency); Expected lifetime items (units). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review cost per item and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

Расчёт, который можно проверить

For this US purchasing example, enter mold / die cost US$1,500.00, initial setup cost US$500.00, expected lifetime items 100,000.00 units. The calculated cost per item is US$0.02000/item. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

Стоимость формы / штампа
1 500 USD
Стоимость начальной настройки
500 USD
Ожидаемое число изделий за срок службы
100 000 шт.
Tooling cost/item = (Mold or die cost + Initial setup) ÷ Expected lifetime items; Tooling cost/1,000 = Tooling cost/item × 1,000
Стоимость одного изделияUS$0,02000/шт.

Частые вопросы

Which units should I use for molded fiber tooling amortization?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two molded fiber tooling amortization results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record mold / die cost (currency), initial setup cost (currency), expected lifetime items (units) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

Перед использованием результата проверьте показанную формулу, единицы измерения и допущения.

Методика, единицы и допущения о материале ↗