ИНСТРУМЕНТ 133 / 136

Packaging Price Tier Comparison Calculator — US Units

Packaging Price Tier Comparison connects the figures on a US supplier quote with the quantity used by your packaging operation. Have units needed (units), tier a order quantity (units), tier a unit price (currency) ready before you start.

Ваши параметры

шт.
шт.
USD
шт.
USD

Только обозначение валюты. Курс не пересчитывается.

Результаты обновляются при изменении данных. Расчёт сохраняется только по вашему выбору.
Расчёт в реальном времени

Сумма закупки для уровня A

US$2 500,00
Сумма закупки для уровня BUS$3 300,00
Разница денежных затрат между уровнями B и AUS$800,00
Излишек единиц для уровня A0,00 шт.
Излишек единиц для уровня B5 000,00 шт.

Количество на обоих уровнях должно покрывать введённую потребность.

Доставка, оснастка, хранение, устаревание и будущая потребность исключены.

Предложения должны иметь сопоставимые спецификации и одну валюту.

Стоимость заказа по ступени = Количество заказа × Цена единицы; Остаток = Количество заказа − Потребность

Units needed: 10000 units; Tier A order quantity: 10000 units; Tier A unit price: 0.25 USD; Tier B order quantity: 15000 units; Tier B unit price: 0.22 USD → US$2 500,00

Рассчитано по вашим данным. Подтвердите параметры у поставщика.

Понятное объяснение формулы.

Стоимость заказа по ступени = Количество заказа × Цена единицы; Остаток = Количество заказа − Потребность

The result answers a specific purchasing question: Work out packaging price tier comparison with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read tier a purchase total in your selected currency. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

Как пользоваться калькулятором

  1. 01

    Collect Units needed (units); Tier A order quantity (units); Tier A unit price (currency); Tier B order quantity (units); Tier B unit price (currency). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review tier a purchase total and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

Расчёт, который можно проверить

For this US purchasing example, enter units needed 10,000.00 units, tier a order quantity 10,000.00 units, tier a unit price US$0.2500, tier b order quantity 15,000.00 units. The calculated tier a purchase total is US$2,500.00. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

Требуемое количество единиц
10 000 шт.
Количество заказа для уровня A
10 000 шт.
Цена за единицу для уровня A
0,25 USD
Количество заказа для уровня B
15 000 шт.
Цена за единицу для уровня B
0,22 USD
Tier order cost = Order quantity × Unit price; Surplus = Order quantity − Units needed
Сумма закупки для уровня AUS$2 500,00

Частые вопросы

Which units should I use for packaging price tier comparison?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two packaging price tier comparison results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record units needed (units), tier a order quantity (units), tier a unit price (currency), tier b order quantity (units) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

Перед использованием результата проверьте показанную формулу, единицы измерения и допущения.

Методика, единицы и допущения о материале ↗