أداة 94 / 136

Thermoformed Part Material Weight Calculator — US Units

Thermoformed Part Material Weight connects the figures on a US supplier quote with the quantity used by your packaging operation. Have web width (inch), machine pitch (inch), parts across (units) ready before you start.

مواصفاتك

وحدة
g/m²
تتحدّث النتائج أثناء التعديل. لا يُحفظ شيء حتى تختار الحفظ.
حساب فوري

حصة إجمالي مادة الورقة لكل قطعة

0.0794 lb/part
إجمالي مساحة الشريط لكل قطعة0.6458 ft²/part
الحصة الإجمالية لكل 1,000 قطعة79.37 lb/1,000 parts

هذا تخصيص إجمالي للشريط وليس وزن القطعة النهائية. يشمل الفرق هيكل القصاصات وكل مادة خارج الجزء المحتفظ به.

يفترض صفًا واحدًا من القطع في اتجاه الماكينة لكل خطوة مدخلة؛ أدرج جميع التجاويف عبر ذلك التكرار.

Gross lb/part = Web width(in) × Pitch(in) ÷ (144 × Parts across) × Sheet GSM × 0.0002048161436

Web width: 31.496062992125985 inch; Machine pitch: 11.811023622047244 inch; Parts across: 4 units; Sheet GSM: 600 g/m² → 0.0794 lb/part

محسوب من مدخلاتك. أكّد المواصفات مع المورد.

المعادلة بوضوح.

Gross lb/part = Web width(in) × Pitch(in) ÷ (144 × Parts across) × Sheet GSM × 0.0002048161436

The result answers a specific purchasing question: Work out thermoformed part material weight with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read gross sheet material allocation per part in lb/part. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

كيفية استخدام هذه الحاسبة

  1. 01

    Collect Web width (inch); Machine pitch (inch); Parts across (units); Sheet GSM (g/m²). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review gross sheet material allocation per part and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

حساب يمكنك التحقق منه

For this US purchasing example, enter web width 31.50 inch, machine pitch 11.81 inch, parts across 4.00 units, sheet gsm 600.00 g/m². The calculated gross sheet material allocation per part is 0.0794 lb/part. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

عرض الشريط
31.496063 inch
خطوة الآلة
11.8110236 inch
الأجزاء عبر العرض
4 وحدات
وزن الصفيحة لكل متر مربع
600 g/m²
Gross lb/part = Web width(in) × Pitch(in) ÷ (144 × Parts across) × Sheet GSM × 0.0002048161436
حصة إجمالي مادة الورقة لكل قطعة0.0794 lb/part

الأسئلة الشائعة

Which units should I use for thermoformed part material weight?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two thermoformed part material weight results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record web width (inch), machine pitch (inch), parts across (units), sheet gsm (g/m²) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

تحقق من المعادلة والوحدات والافتراضات المعروضة قبل استخدام النتيجة.

الطريقة والوحدات وافتراضات المواد ↗