Thermoforming Sheet Weight Calculator — US Units
Thermoforming Sheet Weight connects the figures on a US supplier quote with the quantity used by your packaging operation. Have sheet / web width (inch), sheet / web length (ft), sheet thickness (mil) ready before you start.
مواصفاتك
كثافة توضيحية. استخدم المواصفة الفعلية للبوليمر أو التركيبة.
كثافة نموذجية. تختلف الفعلية حسب درجة الراتنج وتركيبته. يمكنك تعديل القيمة أعلاه.
وزن مادة الورقة أو الشريط
تُدخل الكثافة ولا تُستنتج من قطعة نهائية. قد تتطلب الصفائح الرغوية أو متعددة الطبقات كثافة فعالة مقاسة أو وزنًا مساحيًا فعليًا.
Sheet GSM = Thickness(mil) × 25.4 × Density(g/cm³); Sheet lb = Width(in) × Length(in) ÷ 144 × Sheet GSM × 0.0002048161436
Sheet / web width: 31.496062992125985 inch; Sheet / web length: 3280.839895013123 ft; Sheet thickness: 19.68503937007874 mil; Actual or assumed sheet density: 1.35 g/cm³ → 1,190.50 lbمحسوب من مدخلاتك. أكّد المواصفات مع المورد.
المعادلة بوضوح.
The result answers a specific purchasing question: Work out thermoforming sheet weight with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read sheet / web material weight in lb. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.
كيفية استخدام هذه الحاسبة
- 01
Collect Sheet / web width (inch); Sheet / web length (ft); Sheet thickness (mil); Actual or assumed sheet density (g/cm³). Leave optional unknown values blank rather than substituting zero.
- 02
Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.
- 03
Review sheet / web material weight and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.
حساب يمكنك التحقق منه
For this US purchasing example, enter sheet / web width 31.50 inch, sheet / web length 3,280.84 ft, sheet thickness 19.69 mil, actual or assumed sheet density 1.35 g/cm³. The calculated sheet / web material weight is 1,190.50 lb. The table lists the remaining inputs and results so the scenario can be checked or reproduced.
- عرض الصفيحة / الشريط
- 31.496063 inch
- طول الصفيحة / الشريط
- 3,280.8399 ft
- سماكة الصفيحة
- 19.6850394 مل
- كثافة الصفيحة الفعلية أو المفترضة
- 1.35 g/cm³
Sheet GSM = Thickness(mil) × 25.4 × Density(g/cm³); Sheet lb = Width(in) × Length(in) ÷ 144 × Sheet GSM × 0.0002048161436الأسئلة الشائعة
Which units should I use for thermoforming sheet weight?
Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.
Can I compare two thermoforming sheet weight results directly?
Yes, when both runs use the same specification, purchasing boundary and included charges. Record sheet / web width (inch), sheet / web length (ft), sheet thickness (mil), actual or assumed sheet density (g/cm³) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.
تحقق من المعادلة والوحدات والافتراضات المعروضة قبل استخدام النتيجة.
الطريقة والوحدات وافتراضات المواد ↗