WERKZEUG 54 / 136

Packs per lb Calculator — US Units

Packs per lb connects the figures on a US supplier quote with the quantity used by your packaging operation. Have web width (inch), print / pack repeat (inch), lanes across the web (lanes) ready before you start.

Ihre Spezifikationen

lanes
g/m²

Verwenden Sie nach Möglichkeit das tatsächliche Flächengewicht des Lieferanten oder einen Messwert.

Ergebnisse werden beim Bearbeiten aktualisiert. Gespeichert wird erst auf Ihre Anweisung.
Laufende Berechnung

Nominal packs per lb

56,70 packs/lb
Foliengewicht je Packung0,0176 lb/pack
Folienfläche je Packung1,08 ft²/pack

Nominale Ergiebigkeit vor Prozessverlusten. Verwenden Sie die tatsächliche Produktionsbahngeometrie, nicht nur die fertigen Außenflächenmaße.

Area/pack(ft²) = Width(in) × Repeat(in) ÷ (144 × Lanes); Packs/lb = 1 ÷ (Area/pack × GSM × 0.0002048161436)

Web width: 31.496062992125985 inch; Print / pack repeat: 9.84251968503937 inch; Lanes across the web: 2 lanes; Film GSM: 80 g/m² → 56,70 packs/lb

Aus Ihren Eingaben berechnet. Bestätigen Sie die Spezifikationen mit Ihrem Lieferanten.

Die Formel verständlich erklärt.

Area/pack(ft²) = Width(in) × Repeat(in) ÷ (144 × Lanes); Packs/lb = 1 ÷ (Area/pack × GSM × 0.0002048161436)

The result answers a specific purchasing question: Work out packs per lb with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read nominal packs per lb in packs/lb. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

So verwenden Sie diesen Rechner

  1. 01

    Collect Web width (inch); Print / pack repeat (inch); Lanes across the web (lanes); Film GSM (g/m²). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review nominal packs per lb and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

Eine überprüfbare Berechnung

For this US purchasing example, enter web width 31.50 inch, print / pack repeat 9.84 inch, lanes across the web 2.00 lanes, film gsm 80.00 g/m². The calculated nominal packs per lb is 56.70 packs/lb. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

Bahnbreite
31,496063 inch
Druck- / Verpackungsrapport
9,84251969 inch
Bahnen nebeneinander
2 lanes
Flächengewicht der Folie
80 g/m²
Area/pack(ft²) = Width(in) × Repeat(in) ÷ (144 × Lanes); Packs/lb = 1 ÷ (Area/pack × GSM × 0.0002048161436)
Nominal packs per lb56,70 packs/lb

Häufige Fragen

Which units should I use for packs per lb?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two packs per lb results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record web width (inch), print / pack repeat (inch), lanes across the web (lanes), film gsm (g/m²) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

Prüfen Sie die angezeigte Formel, die Einheiten und die Annahmen, bevor Sie das Ergebnis verwenden.

Methode, Einheiten und Materialannahmen ↗