Shrink Sleeve Cost per Unit Calculator — US Units
Shrink Sleeve Cost per Unit connects the figures on a US supplier quote with the quantity used by your packaging operation. Have layflat width (inch), sleeve cut length (inch), film gsm (g/m²) ready before you start.
Ihre Spezifikationen
Nur Einheitenbezeichnung. Keine Währungsumrechnung.
Folienmaterialkosten je Gutsleeve
Die Flachbreite ist die Hälfte des geöffneten Schlauchumfangs, daher enthält die Fläche beide Seiten. Zusätzliche Nahtüberlappung oder Randbeschnitt liegen außerhalb dieser nominalen Geometrie.
Ausschuss ist der verlorene Anteil des Bruttoeinsatzes. Bruttobedarf = Gutausbringung ÷ (1 − Ausschuss/100).
Naht-, Druck- und Verarbeitungskosten sind separat, sofern nicht eingegeben.
Sleeve ft² = 2 × Layflat width(in) × Cut length(in) ÷ 144; Cost/good sleeve = Sleeve ft² × Price/ft² ÷ (1 − Waste fraction)
Layflat width: 3.937007874015748 inch; Sleeve cut length: 5.905511811023622 inch; Film GSM: 65 g/m²; Film price on selected basis: 1.3607771100000001 USD/lb; Process loss on gross input: 5 %; Additional seaming / printing / conversion per sleeve: 0 USD/unit → US$0,00616/sleeveAus Ihren Eingaben berechnet. Bestätigen Sie die Spezifikationen mit Ihrem Lieferanten.
Die Formel verständlich erklärt.
The result answers a specific purchasing question: Work out shrink sleeve cost per unit with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read film material cost per good sleeve in your selected currency/sleeve. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.
So verwenden Sie diesen Rechner
- 01
Collect Layflat width (inch); Sleeve cut length (inch); Film GSM (g/m²); Film thickness (mil); Entered film density (g/cm³); Film price on selected basis (currency/lb); Process loss on gross input (%); Additional seaming / printing / conversion per sleeve (currency/unit). Leave optional unknown values blank rather than substituting zero.
- 02
Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.
- 03
Review film material cost per good sleeve and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.
Eine überprüfbare Berechnung
For this US purchasing example, enter layflat width 3.94 inch, sleeve cut length 5.91 inch, film gsm 65.00 g/m², film price on selected basis US$1.3608/lb. The calculated film material cost per good sleeve is US$0.00616/sleeve. The table lists the remaining inputs and results so the scenario can be checked or reproduced.
- Flachliegende Schlauchbreite
- 3,93700787 inch
- Sleeve-Schnittlänge
- 5,90551181 inch
- Flächengewicht der Folie
- 65 g/m²
- Folienpreis auf gewählter Basis
- 1,36077711 USD/lb
- Prozessverlust am Bruttoeinsatz
- 5 %
- Zusätzliche Naht / Druck / Verarbeitung je Sleeve
- 0 USD/Einheit
Sleeve ft² = 2 × Layflat width(in) × Cut length(in) ÷ 144; Cost/good sleeve = Sleeve ft² × Price/ft² ÷ (1 − Waste fraction)Häufige Fragen
Which units should I use for shrink sleeve cost per unit?
Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.
Can I compare two shrink sleeve cost per unit results directly?
Yes, when both runs use the same specification, purchasing boundary and included charges. Record layflat width (inch), sleeve cut length (inch), film gsm (g/m²), film thickness (mil) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.
Prüfen Sie die angezeigte Formel, die Einheiten und die Annahmen, bevor Sie das Ergebnis verwenden.
Methode, Einheiten und Materialannahmen ↗