HERRAMIENTA 121 / 136

Blister Material Requirement Calculator — US Units

Blister Material Requirement connects the figures on a US supplier quote with the quantity used by your packaging operation. Have target good packs (units), common web width (inch), machine pitch (inch) ready before you start.

Tus especificaciones

unidades
unidades
g/m²
g/m²
%
Los resultados se actualizan al editar. No se guarda nada hasta que tú lo decidas.
Cálculo en tiempo real

Total bruto de materiales de formado y sellado

95,15 lb
Longitud lineal bruta por banda1151,17 ft
Material bruto de formado81,22 lb
Material bruto de sellado13,92 lb
Superficie bruta de cada banda1133,04 ft²

La merma es la fracción perdida de la entrada bruta. Necesidad bruta = producción conforme ÷ (1 − merma/100).

Este modelo supone iguales anchos y pasos de formado y sellado. Añada pérdidas fijas de arranque aparte; las necesidades son de material bruto continuo, sin redondeo a ciclos completos.

Gross packs = Good target ÷ (1 − Waste fraction); Web length(ft) = Gross packs × Pitch(in) ÷ (12 × Packs across)

Target good packs: 10000 units; Common web width: 11.811023622047244 inch; Machine pitch: 3.937007874015748 inch; Packs across: 3 units; Forming web GSM: 350 g/m²; Lidding GSM: 60 g/m²; Process loss on gross input: 5 % → 95,15 lb

Calculado con tus datos. Confirma las especificaciones con tu proveedor.

La fórmula, explicada.

Gross packs = Good target ÷ (1 − Waste fraction); Web length(ft) = Gross packs × Pitch(in) ÷ (12 × Packs across)

The result answers a specific purchasing question: Work out blister material requirement with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read total gross forming and lidding material in lb. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

Cómo usar esta calculadora

  1. 01

    Collect Target good packs (units); Common web width (inch); Machine pitch (inch); Packs across (units); Forming web GSM (g/m²); Lidding GSM (g/m²); Process loss on gross input (%). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review total gross forming and lidding material and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

Un cálculo que puedes comprobar

For this US purchasing example, enter target good packs 10,000.00 units, common web width 11.81 inch, machine pitch 3.94 inch, packs across 3.00 units. The calculated total gross forming and lidding material is 95.15 lb. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

Objetivo de envases conformes
10.000 unidades
Ancho común de banda
11,8110236 inch
Paso de máquina
3,93700787 inch
Envases a lo ancho
3 unidades
Gramaje de la banda de formado
350 g/m²
Gramaje del material de sellado
60 g/m²
Pérdida sobre entrada bruta
5 %
Gross packs = Good target ÷ (1 − Waste fraction); Web length(ft) = Gross packs × Pitch(in) ÷ (12 × Packs across)
Total bruto de materiales de formado y sellado95,15 lb

Preguntas frecuentes

Which units should I use for blister material requirement?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two blister material requirement results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record target good packs (units), common web width (inch), machine pitch (inch), packs across (units) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

Comprueba la fórmula, las unidades y los supuestos mostrados antes de utilizar el resultado.

Método, unidades y supuestos del material ↗