HERRAMIENTA 38 / 136

Roll Diameter from Weight Calculator — US Units

Roll Diameter from Weight connects the figures on a US supplier quote with the quantity used by your packaging operation. Have net film weight (lb), web width (inch), film gsm (g/m²) ready before you start.

Tus especificaciones

g/m²

Usa el gramaje del proveedor o el medido, si está disponible.

Mida el exterior del mandril, no su diámetro interior.

Los resultados se actualizan al editar. No se guarda nada hasta que tú lo decidas.
Cálculo en tiempo real

Diámetro exterior estimado del rollo

14,49 inch
Longitud lineal calculada4101,05 ft

Estimación geométrica: supone espesor uniforme, bobinado compacto y ausencia de aire atrapado. La longitud real puede variar.

Se utiliza el diámetro EXTERIOR del mandril; el diámetro interior nominal no lo sustituye.

Length(ft) = Net lb ÷ (Width(in) ÷ 12 × GSM × 0.0002048161436); OD(in) = √(Core(in)² + 48 × Thickness(mil) ÷ 1,000 × Length(ft) ÷ π)

Net film weight: 176.36980974790205 lb; Web width: 31.496062992125985 inch; Film GSM: 80 g/m²; Film thickness: 3.149606299212598 mil; Core OUTER diameter: 3.543307086614173 inch → 14,49 inch

Calculado con tus datos. Confirma las especificaciones con tu proveedor.

La fórmula, explicada.

Length(ft) = Net lb ÷ (Width(in) ÷ 12 × GSM × 0.0002048161436); OD(in) = √(Core(in)² + 48 × Thickness(mil) ÷ 1,000 × Length(ft) ÷ π)

The result answers a specific purchasing question: Work out roll diameter from weight with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read estimated roll outer diameter in inch. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

Cómo usar esta calculadora

  1. 01

    Collect Net film weight (lb); Web width (inch); Film GSM (g/m²); Film thickness (mil); Core OUTER diameter (inch). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review estimated roll outer diameter and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

Un cálculo que puedes comprobar

For this US purchasing example, enter net film weight 176.37 lb, web width 31.50 inch, film gsm 80.00 g/m², film thickness 3.15 mil. The calculated estimated roll outer diameter is 14.49 inch. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

Peso neto del film
176,36981 lb
Ancho de banda
31,496063 inch
Gramaje del film
80 g/m²
Espesor del film
3,1496063 mil
Diámetro EXTERIOR del mandril
3,54330709 inch
Length(ft) = Net lb ÷ (Width(in) ÷ 12 × GSM × 0.0002048161436); OD(in) = √(Core(in)² + 48 × Thickness(mil) ÷ 1,000 × Length(ft) ÷ π)
Diámetro exterior estimado del rollo14,49 inch

Preguntas frecuentes

Which units should I use for roll diameter from weight?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two roll diameter from weight results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record net film weight (lb), web width (inch), film gsm (g/m²), film thickness (mil) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

Comprueba la fórmula, las unidades y los supuestos mostrados antes de utilizar el resultado.

Método, unidades y supuestos del material ↗