Remaining Film on Roll Calculator — US Units
Remaining Film on Roll connects the figures on a US supplier quote with the quantity used by your packaging operation. Have roll outer diameter (inch), core outer diameter (inch), film thickness (mil) ready before you start.
Vos spécifications
Mesurez l’extérieur du mandrin, pas son alésage.
Utilisez le grammage réel du fournisseur ou une mesure, si disponible.
Longueur restante estimée
Estimation géométrique : suppose une épaisseur uniforme, un bobinage serré et aucune inclusion d’air. La longueur réelle peut différer.
Le diamètre EXTÉRIEUR du mandrin est utilisé ; l’alésage nominal ne peut pas le remplacer.
Remaining ft = π × (Current OD(in)² − Core OD(in)²) ÷ (48 × Thickness(mil) ÷ 1,000); Area(ft²) = Remaining ft × Width(in) ÷ 12
Roll outer diameter: 13.779527559055119 inch; Core OUTER diameter: 3.543307086614173 inch; Film thickness: 3.149606299212598 mil; Web width: 31.496062992125985 inch; Film GSM: 80 g/m² → 3 684,77 ftCalculé à partir de vos données. Confirmez les spécifications avec votre fournisseur.
La formule expliquée.
The result answers a specific purchasing question: Work out remaining film on roll with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read estimated remaining length in ft. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.
Comment utiliser ce calculateur
- 01
Collect Roll outer diameter (inch); Core OUTER diameter (inch); Film thickness (mil); Web width (inch); Film GSM (g/m²). Leave optional unknown values blank rather than substituting zero.
- 02
Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.
- 03
Review estimated remaining length and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.
Un calcul que vous pouvez vérifier
For this US purchasing example, enter roll outer diameter 13.78 inch, core outer diameter 3.54 inch, film thickness 3.15 mil, web width 31.50 inch. The calculated estimated remaining length is 3,684.77 ft. The table lists the remaining inputs and results so the scenario can be checked or reproduced.
- Diamètre extérieur de bobine
- 13,7795276 inch
- Diamètre EXTÉRIEUR du mandrin
- 3,54330709 inch
- Épaisseur du film
- 3,1496063 mil
- Largeur de bande
- 31,496063 inch
- Grammage du film
- 80 g/m²
Remaining ft = π × (Current OD(in)² − Core OD(in)²) ÷ (48 × Thickness(mil) ÷ 1,000); Area(ft²) = Remaining ft × Width(in) ÷ 12Questions fréquentes
Which units should I use for remaining film on roll?
Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.
Can I compare two remaining film on roll results directly?
Yes, when both runs use the same specification, purchasing boundary and included charges. Record roll outer diameter (inch), core outer diameter (inch), film thickness (mil), web width (inch) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.
Vérifiez la formule, les unités et les hypothèses affichées avant d’utiliser le résultat.
Méthode, unités et hypothèses sur les matériaux ↗