OUTIL 37 / 136

Roll Weight from Diameter Calculator — US Units

Roll Weight from Diameter connects the figures on a US supplier quote with the quantity used by your packaging operation. Have roll outer diameter (inch), core outer diameter (inch), film thickness (mil) ready before you start.

Vos spécifications

Mesurez l’extérieur du mandrin, pas son alésage.

g/m²

Utilisez le grammage réel du fournisseur ou une mesure, si disponible.

Les résultats s’actualisent pendant la saisie. Rien n’est enregistré sans votre choix.
Calcul en direct

Poids net estimé du film

158,47 lb
Longueur estimée de la bobine3 684,77 ft
Surface estimée du film9 671,33 ft²

Estimation géométrique : suppose une épaisseur uniforme, un bobinage serré et aucune inclusion d’air. La longueur réelle peut différer.

Le diamètre EXTÉRIEUR du mandrin est utilisé ; l’alésage nominal ne peut pas le remplacer.

Length(ft) = π × (OD(in)² − Core(in)²) ÷ (48 × Thickness(mil) ÷ 1,000); Net lb = Length(ft) × Width(in) ÷ 12 × GSM × 0.0002048161436

Roll outer diameter: 13.779527559055119 inch; Core OUTER diameter: 3.543307086614173 inch; Film thickness: 3.149606299212598 mil; Web width: 31.496062992125985 inch; Film GSM: 80 g/m² → 158,47 lb

Calculé à partir de vos données. Confirmez les spécifications avec votre fournisseur.

La formule expliquée.

Length(ft) = π × (OD(in)² − Core(in)²) ÷ (48 × Thickness(mil) ÷ 1,000); Net lb = Length(ft) × Width(in) ÷ 12 × GSM × 0.0002048161436

The result answers a specific purchasing question: Work out roll weight from diameter with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read estimated net film weight in lb. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

Comment utiliser ce calculateur

  1. 01

    Collect Roll outer diameter (inch); Core OUTER diameter (inch); Film thickness (mil); Web width (inch); Film GSM (g/m²). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review estimated net film weight and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

Un calcul que vous pouvez vérifier

For this US purchasing example, enter roll outer diameter 13.78 inch, core outer diameter 3.54 inch, film thickness 3.15 mil, web width 31.50 inch. The calculated estimated net film weight is 158.47 lb. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

Diamètre extérieur de bobine
13,7795276 inch
Diamètre EXTÉRIEUR du mandrin
3,54330709 inch
Épaisseur du film
3,1496063 mil
Largeur de bande
31,496063 inch
Grammage du film
80 g/m²
Length(ft) = π × (OD(in)² − Core(in)²) ÷ (48 × Thickness(mil) ÷ 1,000); Net lb = Length(ft) × Width(in) ÷ 12 × GSM × 0.0002048161436
Poids net estimé du film158,47 lb

Questions fréquentes

Which units should I use for roll weight from diameter?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two roll weight from diameter results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record roll outer diameter (inch), core outer diameter (inch), film thickness (mil), web width (inch) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

Vérifiez la formule, les unités et les hypothèses affichées avant d’utiliser le résultat.

Méthode, unités et hypothèses sur les matériaux ↗