OUTIL 38 / 136

Roll Diameter from Weight Calculator — US Units

Roll Diameter from Weight connects the figures on a US supplier quote with the quantity used by your packaging operation. Have net film weight (lb), web width (inch), film gsm (g/m²) ready before you start.

Vos spécifications

g/m²

Utilisez le grammage réel du fournisseur ou une mesure, si disponible.

Mesurez l’extérieur du mandrin, pas son alésage.

Les résultats s’actualisent pendant la saisie. Rien n’est enregistré sans votre choix.
Calcul en direct

Diamètre extérieur estimé de la bobine

14,49 inch
Longueur déroulée calculée4 101,05 ft

Estimation géométrique : suppose une épaisseur uniforme, un bobinage serré et aucune inclusion d’air. La longueur réelle peut différer.

Le diamètre EXTÉRIEUR du mandrin est utilisé ; l’alésage nominal ne peut pas le remplacer.

Length(ft) = Net lb ÷ (Width(in) ÷ 12 × GSM × 0.0002048161436); OD(in) = √(Core(in)² + 48 × Thickness(mil) ÷ 1,000 × Length(ft) ÷ π)

Net film weight: 176.36980974790205 lb; Web width: 31.496062992125985 inch; Film GSM: 80 g/m²; Film thickness: 3.149606299212598 mil; Core OUTER diameter: 3.543307086614173 inch → 14,49 inch

Calculé à partir de vos données. Confirmez les spécifications avec votre fournisseur.

La formule expliquée.

Length(ft) = Net lb ÷ (Width(in) ÷ 12 × GSM × 0.0002048161436); OD(in) = √(Core(in)² + 48 × Thickness(mil) ÷ 1,000 × Length(ft) ÷ π)

The result answers a specific purchasing question: Work out roll diameter from weight with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read estimated roll outer diameter in inch. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

Comment utiliser ce calculateur

  1. 01

    Collect Net film weight (lb); Web width (inch); Film GSM (g/m²); Film thickness (mil); Core OUTER diameter (inch). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review estimated roll outer diameter and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

Un calcul que vous pouvez vérifier

For this US purchasing example, enter net film weight 176.37 lb, web width 31.50 inch, film gsm 80.00 g/m², film thickness 3.15 mil. The calculated estimated roll outer diameter is 14.49 inch. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

Masse nette du film
176,36981 lb
Largeur de bande
31,496063 inch
Grammage du film
80 g/m²
Épaisseur du film
3,1496063 mil
Diamètre EXTÉRIEUR du mandrin
3,54330709 inch
Length(ft) = Net lb ÷ (Width(in) ÷ 12 × GSM × 0.0002048161436); OD(in) = √(Core(in)² + 48 × Thickness(mil) ÷ 1,000 × Length(ft) ÷ π)
Diamètre extérieur estimé de la bobine14,49 inch

Questions fréquentes

Which units should I use for roll diameter from weight?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two roll diameter from weight results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record net film weight (lb), web width (inch), film gsm (g/m²), film thickness (mil) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

Vérifiez la formule, les unités et les hypothèses affichées avant d’utiliser le résultat.

Méthode, unités et hypothèses sur les matériaux ↗