OUTIL 93 / 136

Thermoforming Sheet Weight Calculator — US Units

Thermoforming Sheet Weight connects the figures on a US supplier quote with the quantity used by your packaging operation. Have sheet / web width (inch), sheet / web length (ft), sheet thickness (mil) ready before you start.

Vos spécifications

g/cm³

Masse volumique illustrative. Utilisez la spécification réelle du polymère ou de la formulation.

Masse volumique typique. La valeur réelle varie selon grade et formulation. Vous pouvez modifier la valeur ci-dessus.

Les résultats s’actualisent pendant la saisie. Rien n’est enregistré sans votre choix.
Calcul en direct

Poids de matière en feuille ou en bande

1 190,50 lb
Grammage calculé de la feuille675,00 g/m²
Surface de feuille ou de bande8 611,13 ft²

La masse volumique est saisie, pas déduite d’une pièce finie. Les feuilles expansées ou multicouches peuvent nécessiter une masse volumique effective mesurée ou un grammage réel.

Sheet GSM = Thickness(mil) × 25.4 × Density(g/cm³); Sheet lb = Width(in) × Length(in) ÷ 144 × Sheet GSM × 0.0002048161436

Sheet / web width: 31.496062992125985 inch; Sheet / web length: 3280.839895013123 ft; Sheet thickness: 19.68503937007874 mil; Actual or assumed sheet density: 1.35 g/cm³ → 1 190,50 lb

Calculé à partir de vos données. Confirmez les spécifications avec votre fournisseur.

La formule expliquée.

Sheet GSM = Thickness(mil) × 25.4 × Density(g/cm³); Sheet lb = Width(in) × Length(in) ÷ 144 × Sheet GSM × 0.0002048161436

The result answers a specific purchasing question: Work out thermoforming sheet weight with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read sheet / web material weight in lb. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

Comment utiliser ce calculateur

  1. 01

    Collect Sheet / web width (inch); Sheet / web length (ft); Sheet thickness (mil); Actual or assumed sheet density (g/cm³). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review sheet / web material weight and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

Un calcul que vous pouvez vérifier

For this US purchasing example, enter sheet / web width 31.50 inch, sheet / web length 3,280.84 ft, sheet thickness 19.69 mil, actual or assumed sheet density 1.35 g/cm³. The calculated sheet / web material weight is 1,190.50 lb. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

Largeur de feuille / bande
31,496063 inch
Longueur de feuille / bande
3 280,8399 ft
Épaisseur de feuille
19,6850394 mil
Masse volumique réelle ou supposée de feuille
1,35 g/cm³
Sheet GSM = Thickness(mil) × 25.4 × Density(g/cm³); Sheet lb = Width(in) × Length(in) ÷ 144 × Sheet GSM × 0.0002048161436
Poids de matière en feuille ou en bande1 190,50 lb

Questions fréquentes

Which units should I use for thermoforming sheet weight?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two thermoforming sheet weight results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record sheet / web width (inch), sheet / web length (ft), sheet thickness (mil), actual or assumed sheet density (g/cm³) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

Vérifiez la formule, les unités et les hypothèses affichées avant d’utiliser le résultat.

Méthode, unités et hypothèses sur les matériaux ↗