ツール 121 / 136

Blister Material Requirement Calculator — US Units

Blister Material Requirement connects the figures on a US supplier quote with the quantity used by your packaging operation. Have target good packs (units), common web width (inch), machine pitch (inch) ready before you start.

仕様を入力

個
個
g/m²
g/m²
%
入力を変更すると結果も更新されます。保存を選ぶまでデータは保存されません。
リアルタイム計算

成形材料・蓋材の総使用量合計

95.15 lb
各ウェブの総巻長1,151.17 ft
総成形材料量81.22 lb
総蓋材量13.92 lb
各ウェブの総面積1,133.04 ft²

ロスは総投入量のうち失われる割合です。総必要量=良品出力÷(1-ロス百分率/100)。

成形材と蓋材の幅とピッチが等しい計画モデルです。固定立上げロスは別途追加してください。必要量は連続した総材料量であり、機械の整数サイクルへの丸めは行いません。

Gross packs = Good target ÷ (1 − Waste fraction); Web length(ft) = Gross packs × Pitch(in) ÷ (12 × Packs across)

Target good packs: 10000 units; Common web width: 11.811023622047244 inch; Machine pitch: 3.937007874015748 inch; Packs across: 3 units; Forming web GSM: 350 g/m²; Lidding GSM: 60 g/m²; Process loss on gross input: 5 % → 95.15 lb

入力値に基づく計算です。仕様は仕入先に確認してください。

計算式をわかりやすく。

Gross packs = Good target ÷ (1 − Waste fraction); Web length(ft) = Gross packs × Pitch(in) ÷ (12 × Packs across)

The result answers a specific purchasing question: Work out blister material requirement with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read total gross forming and lidding material in lb. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

この計算ツールの使い方

  1. 01

    Collect Target good packs (units); Common web width (inch); Machine pitch (inch); Packs across (units); Forming web GSM (g/m²); Lidding GSM (g/m²); Process loss on gross input (%). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review total gross forming and lidding material and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

検算できる計算例

For this US purchasing example, enter target good packs 10,000.00 units, common web width 11.81 inch, machine pitch 3.94 inch, packs across 3.00 units. The calculated total gross forming and lidding material is 95.15 lb. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

目標良品包装数
10,000 個
共通ウェブ幅
11.8110236 inch
送りピッチ
3.93700787 inch
幅方向の包装数
3 個
成形ウェブ坪量
350 g/m²
蓋材坪量
60 g/m²
総投入量基準の工程ロス
5 %
Gross packs = Good target ÷ (1 − Waste fraction); Web length(ft) = Gross packs × Pitch(in) ÷ (12 × Packs across)
成形材料・蓋材の総使用量合計95.15 lb

よくある質問

Which units should I use for blister material requirement?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two blister material requirement results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record target good packs (units), common web width (inch), machine pitch (inch), packs across (units) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

結果を使用する前に、表示された式、単位、前提条件を確認してください。

計算方法・単位・材料の前提条件 ↗