Material Required for Order Calculator — US Units
Material Required for Order connects the figures on a US supplier quote with the quantity used by your packaging operation. Have target good finished units (units), web width (inch), print / pack repeat (inch) ready before you start.
仕様を入力
仕入先の実際の坪量または実測値がある場合は、それを使用してください。
総投入量に対する損失率です。
必要な総フィルム量
ロス率は総材料投入量に対する損失の割合です。総必要量=正味必要量÷(1-ロス率)で求めます。
ウェブ幅とリピートは実際の生産割当を含めてください。追加の固定段取りロスは別途計画してください。
Gross pack equivalents = Good target ÷ (1 − Waste fraction); Length(ft) = Gross pack equivalents × Repeat(in) ÷ (12 × Lanes); Area(ft²) = Length(ft) × Width(in) ÷ 12
Target good finished units: 100000 units; Web width: 31.496062992125985 inch; Print / pack repeat: 9.84251968503937 inch; Lanes across the web: 2 lanes; Film GSM: 80 g/m²; Process waste: 5 % → 1,856.52 lb入力値に基づく計算です。仕様は仕入先に確認してください。
計算式をわかりやすく。
The result answers a specific purchasing question: Work out material required for order with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read gross film required in lb. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.
この計算ツールの使い方
- 01
Collect Target good finished units (units); Web width (inch); Print / pack repeat (inch); Lanes across the web (lanes); Film GSM (g/m²); Process waste (%). Leave optional unknown values blank rather than substituting zero.
- 02
Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.
- 03
Review gross film required and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.
検算できる計算例
For this US purchasing example, enter target good finished units 100,000.00 units, web width 31.50 inch, print / pack repeat 9.84 inch, lanes across the web 2.00 lanes. The calculated gross film required is 1,856.52 lb. The table lists the remaining inputs and results so the scenario can be checked or reproduced.
- 目標良品完成数
- 100,000 個
- ウェブ幅
- 31.496063 inch
- 印刷・包装のリピート長
- 9.84251969 inch
- 幅方向の列数
- 2 lanes
- フィルム坪量
- 80 g/m²
- 工程ロス
- 5 %
Gross pack equivalents = Good target ÷ (1 − Waste fraction); Length(ft) = Gross pack equivalents × Repeat(in) ÷ (12 × Lanes); Area(ft²) = Length(ft) × Width(in) ÷ 12よくある質問
Which units should I use for material required for order?
Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.
Can I compare two material required for order results directly?
Yes, when both runs use the same specification, purchasing boundary and included charges. Record target good finished units (units), web width (inch), print / pack repeat (inch), lanes across the web (lanes) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.
結果を使用する前に、表示された式、単位、前提条件を確認してください。
計算方法・単位・材料の前提条件 ↗