ツール 105 / 136

Metal Can Landed Cost Calculator — US Units

Metal Can Landed Cost connects the figures on a US supplier quote with the quantity used by your packaging operation. Have quoted can body price (currency/unit), total material quote (currency), end / lid price per can (currency/unit) ready before you start.

仕様を入力

USD/unit
USD/unit
個
USD
USD
USD
USD

単位表示のみです。為替換算は行いません。

入力を変更すると結果も更新されます。保存を選ぶまでデータは保存されません。
リアルタイム計算

缶1個当たりの原価

US$0.2650/can
缶1,000個当たりの原価US$265.00/1,000 can
缶1個当たりの運賃配賦額US$0.02500/個
1個当たりの見積部品費US$0.2400/個
1個当たりの注文固定費合計US$0.02500/個
注文の着荷原価合計US$2,650.00

見積額とすべての費用は選択通貨を使用し、為替換算しません。

見積額に運賃や部品が含まれる場合は重ねて加算しないでください。関税は金額で入力します。

缶着地単価 = 缶単価 + 別途底・蓋単価 +(運賃 + 型費 + その他固定費)÷ 数量

Quoted can body price: 0.2 USD/unit; End / lid price per can: 0.04 USD/unit; Order quantity: 10000 units; Freight for this order: 250 USD; Tooling allocated to this order: 0 USD; Customs / duty amount: 0 USD; Other fixed order charges: 0 USD → US$0.2650/can

入力値に基づく計算です。仕様は仕入先に確認してください。

計算式をわかりやすく。

缶着地単価 = 缶単価 + 別途底・蓋単価 +(運賃 + 型費 + その他固定費)÷ 数量

The result answers a specific purchasing question: Work out metal can landed cost with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read cost per can in your selected currency/can. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

この計算ツールの使い方

  1. 01

    Collect Quoted can body price (currency/unit); Total material quote (currency); End / lid price per can (currency/unit); Order quantity (units); Freight for this order (currency); Tooling allocated to this order (currency); Customs / duty amount (currency); Other fixed order charges (currency). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review cost per can and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

検算できる計算例

For this US purchasing example, enter quoted can body price US$0.2000/unit, end / lid price per can US$0.04000/unit, order quantity 10,000.00 units, freight for this order US$250.00. The calculated cost per can is US$0.2650/can. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

缶胴の見積価格
0.2 USD/個
缶1個当たりの底・蓋価格
0.04 USD/個
発注数量
10,000 個
この注文の運賃
250 USD
この注文に配賦する金型費
0 USD
関税額
0 USD
その他の固定注文費
0 USD
Landed/can = Can price + Separate end price + (Freight + Tooling + Other fixed charges) ÷ Quantity
缶1個当たりの原価US$0.2650/can

よくある質問

Which units should I use for metal can landed cost?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two metal can landed cost results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record quoted can body price (currency/unit), total material quote (currency), end / lid price per can (currency/unit), order quantity (units) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

結果を使用する前に、表示された式、単位、前提条件を確認してください。

計算方法・単位・材料の前提条件 ↗