ツール 63 / 136

Molded Fiber Tooling Amortization Calculator — US Units

Molded Fiber Tooling Amortization connects the figures on a US supplier quote with the quantity used by your packaging operation. Have mold / die cost (currency), initial setup cost (currency), expected lifetime items (units) ready before you start.

仕様を入力

USD
USD
個

単位表示のみです。為替換算は行いません。

入力を変更すると結果も更新されます。保存を選ぶまでデータは保存されません。
リアルタイム計算

製品1個当たりの原価

US$0.02000/個
製品1,000個当たりの原価US$20.00/1,000 item
金型・初期段取り費合計US$2,000.00

生涯生産数量は計画上の仮定です。入力額に含めた場合を除き、交換金型と再段取りは含みません。

トレー見積りに金型費が含まれている場合、この配賦額を重ねて加算しないでください。

1個の型費 =(型費 + 初期段取り)÷ 予定生涯数量;1,000個の型費 = 単位型費 × 1,000

Mold / die cost: 1500 USD; Initial setup cost: 500 USD; Expected lifetime items: 100000 units → US$0.02000/個

入力値に基づく計算です。仕様は仕入先に確認してください。

計算式をわかりやすく。

1個の型費 =(型費 + 初期段取り)÷ 予定生涯数量;1,000個の型費 = 単位型費 × 1,000

The result answers a specific purchasing question: Work out molded fiber tooling amortization with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read cost per item in your selected currency/item. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

この計算ツールの使い方

  1. 01

    Collect Mold / die cost (currency); Initial setup cost (currency); Expected lifetime items (units). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review cost per item and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

検算できる計算例

For this US purchasing example, enter mold / die cost US$1,500.00, initial setup cost US$500.00, expected lifetime items 100,000.00 units. The calculated cost per item is US$0.02000/item. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

金型・抜き型費
1,500 USD
初期設定費
500 USD
寿命全体の予定個数
100,000 個
Tooling cost/item = (Mold or die cost + Initial setup) ÷ Expected lifetime items; Tooling cost/1,000 = Tooling cost/item × 1,000
製品1個当たりの原価US$0.02000/個

よくある質問

Which units should I use for molded fiber tooling amortization?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two molded fiber tooling amortization results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record mold / die cost (currency), initial setup cost (currency), expected lifetime items (units) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

結果を使用する前に、表示された式、単位、前提条件を確認してください。

計算方法・単位・材料の前提条件 ↗