ツール 38 / 136

Roll Diameter from Weight Calculator — US Units

Roll Diameter from Weight connects the figures on a US supplier quote with the quantity used by your packaging operation. Have net film weight (lb), web width (inch), film gsm (g/m²) ready before you start.

仕様を入力

g/m²

仕入先の実際の坪量または実測値がある場合は、それを使用してください。

コアの内径ではなく外径を測定してください。

入力を変更すると結果も更新されます。保存を選ぶまでデータは保存されません。
リアルタイム計算

推定ロール外径

14.49 inch
算出した巻長4,101.05 ft

厚さが均一で、きつく巻かれ、空気を巻き込んでいない前提の幾何学的推定です。実際の巻長とは異なる場合があります。

コア外径を使用します。公称内径で代用することはできません。

Length(ft) = Net lb ÷ (Width(in) ÷ 12 × GSM × 0.0002048161436); OD(in) = √(Core(in)² + 48 × Thickness(mil) ÷ 1,000 × Length(ft) ÷ π)

Net film weight: 176.36980974790205 lb; Web width: 31.496062992125985 inch; Film GSM: 80 g/m²; Film thickness: 3.149606299212598 mil; Core OUTER diameter: 3.543307086614173 inch → 14.49 inch

入力値に基づく計算です。仕様は仕入先に確認してください。

計算式をわかりやすく。

Length(ft) = Net lb ÷ (Width(in) ÷ 12 × GSM × 0.0002048161436); OD(in) = √(Core(in)² + 48 × Thickness(mil) ÷ 1,000 × Length(ft) ÷ π)

The result answers a specific purchasing question: Work out roll diameter from weight with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read estimated roll outer diameter in inch. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

この計算ツールの使い方

  1. 01

    Collect Net film weight (lb); Web width (inch); Film GSM (g/m²); Film thickness (mil); Core OUTER diameter (inch). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review estimated roll outer diameter and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

検算できる計算例

For this US purchasing example, enter net film weight 176.37 lb, web width 31.50 inch, film gsm 80.00 g/m², film thickness 3.15 mil. The calculated estimated roll outer diameter is 14.49 inch. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

フィルム正味重量
176.36981 lb
ウェブ幅
31.496063 inch
フィルム坪量
80 g/m²
フィルム厚さ
3.1496063 ミル
コアの外径
3.54330709 inch
Length(ft) = Net lb ÷ (Width(in) ÷ 12 × GSM × 0.0002048161436); OD(in) = √(Core(in)² + 48 × Thickness(mil) ÷ 1,000 × Length(ft) ÷ π)
推定ロール外径14.49 inch

よくある質問

Which units should I use for roll diameter from weight?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two roll diameter from weight results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record net film weight (lb), web width (inch), film gsm (g/m²), film thickness (mil) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

結果を使用する前に、表示された式、単位、前提条件を確認してください。

計算方法・単位・材料の前提条件 ↗