ツール 108 / 136

Tube Landed Cost Calculator — US Units

Tube Landed Cost connects the figures on a US supplier quote with the quantity used by your packaging operation. Have quoted tube body price (currency/unit), total material quote (currency), cap per tube (currency/unit) ready before you start.

仕様を入力

USD/unit
USD/unit
USD/unit
個
USD
USD
USD
USD

単位表示のみです。為替換算は行いません。

入力を変更すると結果も更新されます。保存を選ぶまでデータは保存されません。
リアルタイム計算

チューブ1個当たりの原価

US$0.2650/tube
チューブ1,000個当たりの原価US$265.00/1,000 tube
チューブ1本当たりの運賃配賦額US$0.02500/個
1個当たりの見積部品費US$0.2400/個
1個当たりの注文固定費合計US$0.02500/個
注文の着荷原価合計US$2,650.00

見積額とすべての費用は選択通貨を使用し、為替換算しません。

見積額に運賃や部品が含まれる場合は重ねて加算しないでください。関税は金額で入力します。

チューブ着地単価 = 基本単価 + 別途キャップ + 別途装飾 + 注文固定費 ÷ 数量

Quoted tube body price: 0.2 USD/unit; Cap per tube: 0.04 USD/unit; Additional decoration per tube: 0 USD/unit; Order quantity: 10000 units; Freight for this order: 250 USD; Tooling allocated to this order: 0 USD; Customs / duty amount: 0 USD; Other fixed order charges: 0 USD → US$0.2650/tube

入力値に基づく計算です。仕様は仕入先に確認してください。

計算式をわかりやすく。

チューブ着地単価 = 基本単価 + 別途キャップ + 別途装飾 + 注文固定費 ÷ 数量

The result answers a specific purchasing question: Work out tube landed cost with US purchasing units. Enter the actual specification and compare the result on a consistent order basis. Read cost per tube in your selected currency/tube. Width and repeat measurements describe the actual purchased web or blank; a finished pack dimension is only interchangeable when the layout really uses that dimension. Keep input prices on the unit printed next to each price field. The US view converts the physical quantity and its price denominator together, so changing units preserves the calculated material or order value.

この計算ツールの使い方

  1. 01

    Collect Quoted tube body price (currency/unit); Total material quote (currency); Cap per tube (currency/unit); Additional decoration per tube (currency/unit); Order quantity (units); Freight for this order (currency); Tooling allocated to this order (currency); Customs / duty amount (currency); Other fixed order charges (currency). Leave optional unknown values blank rather than substituting zero.

  2. 02

    Use inches for short dimensions, feet for running length, square feet for coverage and pounds for mass. A US short ton is exactly 2,000 lb; US gallons are not Imperial gallons.

  3. 03

    Review cost per tube and the secondary outputs. Check the quote boundary, then repeat with the competing specification or order quantity.

検算できる計算例

For this US purchasing example, enter quoted tube body price US$0.2000/unit, cap per tube US$0.04000/unit, additional decoration per tube US$0.00000/unit, order quantity 10,000.00 units. The calculated cost per tube is US$0.2650/tube. The table lists the remaining inputs and results so the scenario can be checked or reproduced.

チューブ胴の見積価格
0.2 USD/個
チューブ1本当たりのキャップ費用
0.04 USD/個
チューブ1本当たりの追加装飾費
0 USD/個
発注数量
10,000 個
この注文の運賃
250 USD
この注文に配賦する金型費
0 USD
関税額
0 USD
その他の固定注文費
0 USD
Landed/tube = Base tube price + Separate cap + Separate decoration + Fixed order charges ÷ Quantity
チューブ1個当たりの原価US$0.2650/tube

よくある質問

Which units should I use for tube landed cost?

Use the units shown beside each input. Coverage is in ft², mass is in lb and short dimensions are in inches. GSM and g/cm³ remain explicit technical material properties. The matching Metric edition is linked above the calculator.

Can I compare two tube landed cost results directly?

Yes, when both runs use the same specification, purchasing boundary and included charges. Record quoted tube body price (currency/unit), total material quote (currency), cap per tube (currency/unit), additional decoration per tube (currency/unit) for each run, then investigate any physical or commercial difference instead of treating the lower number alone as a supplier decision.

結果を使用する前に、表示された式、単位、前提条件を確認してください。

計算方法・単位・材料の前提条件 ↗